Fish Hawk X4D Owner'S Manual Download

Page: 10 / 16

10 Fish Hawk Owners Manual

The POWER button turns the display on and off. The display draws 35 mA when

on and .3 mA when off. The display is equipped with a backlight for low-light con-
ditions. Enable the backlight by pressing the UP arrow or turn the backlight off by
pressing the DOWN arrow. The model X4D has three levels of backlighting.

The display has four screen settings. To access each setting press the SET but-

ton, each time the SET button is pressed, the display will move to the next setting.

• Screen #1 allows you to set the gain (sensitivity) with a range of 0-25, the de-

fault is 15. Use the UP and DOWN arrows to adjust.

• Screen #2 allows you to set the temperature unit of measure to Fahrenheit or Cel-

sius, the default is Fahrenheit. Use the UP and DOWN arrows to adjust.

• Screen #3 allows you to set the speed unit of measure to MPH, KNOTS, or

KPH, the default is MPH. Use the UP and DOWN arrows to adjust.

• Screen #4 allows you to calibrate the sensor readings, + or – 5 degrees F on the

temperature, and up to two-times adjustment for the speed. Use the
UP and DOWN arrows to adjust. You can exit these screens by press-
ing the POWER button at any time. All changes are saved at that point.

POWER

Button

SET

Button

Arrow

DOWN

Arrow

Probe

Speed

Probe

Temperature

Current

Settings

Surface*

Speed

Surface

Temperature

POWER

Button

SET

Button

Arrow

DOWN

Arrow

Probe

Speed

Probe

Temperature

Current

Settings

Probe*

Depth

Surface

Temperature

Setting the Gain–Screen #1

The gain is also referred to as sensitivity, and ranges

from 0 to 25. The factory default setting of 15 usually

provides excellent results. The gain control only has

an effect on the probe function. Most of the time no

or only small adjustments are necessary. Increasing

the gain allows probe readings to be received from

greater depths. Lower gain settings reduce the pos-

sibility of other sonar or electrical interference, and

also may be necessary in shallow water

Current gain setting

being displayed.

Press UP

arrow to

increase

gain

setting.

Press

DOWN

arrow to

decrease

gain

setting.

Summary of Contents for X4D

















Search results

Summary of Contents for X4D

Reviews:

Related manuals for X4D

Brands by name

Popular brands

Fish Hawk X4D, Owner'S Manual

Search results

Summary of Contents for X4D

Reviews:

Related manuals for X4D

Brands by name

Popular brands