background image

  www.fishhaw electronics.com  5

The Search for the Right Water Temperature

Every body of water has temperature changes from the top to the bottom. There 

are layers of water where the temperature will be significantly different. These are 
differences  are  referred  to  as  “temperature  breaks”  or  the  “thermocline.”  Often 
fish will travel along the thermocline or temperature break, and finding these ar-
eas is key to finding fish

Each species of fish lives in a preferred water temperature range. The chart be-

low shows the preferred water temperature range for the most popular freshwater 
game fish and baitfish species in Fa enheit.

Preferred Water Temperature Ranges

(shown in Fahrenheit) 

Species

Lower Limit

Optimum 

Upper Limit

Brown Trout

44

52

75

Chinook Salmon

40

44

60

Coho Salmon 

44

54

60

Crappie

60

70

75

Kokanee

52

Lake Trout 

40

42

55

Largemouth Bass

50

70

80

Atlantic Salmon

45

50

60

Rainbow Trout 

44

54

63

Smallmouth Bass

50

65

73

Steelhead

42

45

62

Walleye

50

67

76

Alewife

48

54

72

Cisco

53

Emerald Shiner

61

Gizzard Shad

69

Rainbow Smelt

43

50

57

Spottail Shiner

54

Fish suspend in the water column by water temperature. Using your Fish Hawk will 

allow you to find them. With the Fish Hawk you can create a temperature profile of 

the water column by lowering the probe close to the bottom and observing the water 

temperature as you slowly raise the probe to the surface. This will allow you to find the 

correct water temperature for the species you are targeting.

Fish Hawk X4/X4D Components

The Fish Hawk can be purchased as a complete system or as an Upgrade Kit for 

previous models. Replacement Probes are available separately if needed.  Depending 
on which configuration you have purchased, your package will include the following:

Fish Hawk System

• Transducer with 30’ cable 
• Transducer mounting kit
• LCD display 
• Power cord for LCD display
• LCD display stand
• Fish Hawk Probe
• Breakaway cannonball wire safety lead
• Protective rubber probe bumper
• This Owner’s Manual 

Fish Hawk Upgrade Kit 

• LCD display
• LCD display stand
• Fish Hawk Probe
• Breakaway cannonball wire safety lead
• Protective rubber probe bumper
• This Owner’s Manual 

Fish Hawk Probe

• Fish Hawk Probe
• Breakaway cannonball wire safety lead
• Protective rubber probe bumper
• This Owner’s Manual

How the Fish Hawk Operates

The  Fish  Hawk  Probe  is  fastened  to  the  downrigger 

cable just above the downrigger ball and has sensors that 
constantly  monitor  water  temperature  and  speed  as  it 
travels through the water. The probe sends a sonar signal 
with that information to the Transducer mounted on the 
back of the boat. The Transducer, which is hooked up to 
the LCD display, sends the data from the Probe and the 
water’s surface to the liquid crystal display (LCD) mount-
ed in the boat. 

As the water temperature, speed or depth (model X4D 

only) changes, the LCD updates to reflect the new infor-
mation. To compensate for wave action, speed is calculated 
over  a  20-second  period.    The  probe  operates  at  depths 
from 1 to 300 feet.

X4 Digital Display

Transducer

Transmitter

Downrigger 

Ball

Downrigger 

Line

Temperature 

Sensors

Speed 

Sensor

Break-Away 

Lead

Probe

Summary of Contents for X4D

















Reviews: