321144
68
Fault Code: 4
Reason:
The resistance of all the temperature sensors are outside the normal range
(< 660 Ohms).
Primary Action:
Check the 6-way RAST connector at the power/control module.
Secondary Action:
Re-terminate the 6-way RAST connector.
Tertiary Action:
Replace the power/control module.
Fault Code: 5
Reason:
The resistance of the FC sensor is outside the normal range (> 45K Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 6
Reason:
The resistance of the FC sensor is outside the normal range (< 660 Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 7
Reason:
The resistance of the evaporator sensor is outside the normal range (> 45K Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 8
Reason:
The resistance of the evaporator sensor is outside the normal range (< 660 Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 9
Reason:
The resistance of the PC sensor is outside the normal range (> 45K Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 10
Reason:
The resistance of the PC sensor is outside the normal range (< 660 Ohms).
Primary Action:
Check the sensor connection at the power/control module.
Secondary Action:
Replace the sensor.
Fault Code: 11
Reason:
The current measured for the ambient heater, PC fan and FC fan is lower than
expected.
Primary Action:
Check the 6-way fan/LAH RAST connector at the power/control module.
Secondary Action:
Re-terminate the 6-way fan/LAH RAST connector.
Tertiary Action:
Replace the power/control module.
Fault Code: 12
Reason:
The current measured for the ambient heater, PC fan and FC fan is higher than
expected.
Primary Action:
Check the 6-way fan/LAH RAST connector at the power/control module.
Secondary Action:
Re-terminate the 6-way fan/LAH RAST connector.
Tertiary Action:
Replace the power/control module.
Fault Code: 13
Reason:
The low ambient heater is drawing less current than expected. Either the heater or
wiring is open circuit or the heater is faulty.
Primary Action:
Check the wiring and connections at both the heater and the power/control module.
Secondary Action:
Check the ambient heater resistance. If not within limits, replace.
Summary of Contents for 635 Active Smart
