321144
55
9
WATER DISPENSER
9.1
Installation Precautions / Warning
•
DO NOT
use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. (
WARNING
– connect to potable water supply only.)
•
DO NOT
install on line pressures above 827 kPa (119 psi) or below 150kPa (22 psi).
•
DO NOT
use on hot water supply (38
O
C [100
O
F] maximum).
•
DO NOT
cut any length of water tube shorter than 500mm (20 inches).
•
DO NOT
install near electrical wires or water pipes that will be in the path of drilling when selecting the
location of the filter system.
•
DO NOT
mount the filter in such a position that it will be struck by other items, such as wastebaskets, etc.
•
DO NOT
install the filter or any water tubing in direct sunlight, as prolonged exposure to light can weaken
plastic components.
•
DO NOT
install the filter in a location that is susceptible to freezing temperatures as damage to the filter
housing could occur.
•
DO NOT
screw the filter to the refrigerator.
•
DO NOT
install the filter or any water tubing in high temperature areas e.g. in a ceiling cavity.
•
AVOID
contamination of pipes during installation.
•
DO NOT
use copper tubing. The plastic tubing supplied should always be used.
•
DO NOT
continuously dispense water for longer than 2 minutes.
IMPORTANT
•
All connections must be checked for leaks.
•
If unsure of connection process and/or leaks, then contact your local plumber to install and check the
system for you.
•
Ensure that the 6mm (¼”) tubing is routed away from sharp objects, sharp corners (beware of kinking
tube as this will stop water flow), clear of the refrigerator unit compartment and not in a location where it
can be squashed.
•
Ensure that all push-fit connections are firmly pushed into place. The tube should push in 20mm (¾”)
before reaching the stop.
•
If the tubing is removed at any point, re-cut the end and re-insert. The tubing must be fully inserted to
avoid leaks.
•
To remove the tube from connection points, turn off the isolating tap, then push in the collet and gently
pull the tubing at the same time.
9.2
Pressure Dispensing Pad
This pad is located at the rear of the dispensing area and is used to dispense water. Water can be
dispensed by pressing the dispenser pad. The display will light up and the water fill icon will appear when
the water is dispensed.
The dispenser will not operate while the PC door is open.
9.3
Initial Use
Press the glass or container into the pressure-dispensing pad.
Note: Pressing very hard against the water dispensing pad will NOT make the water dispenser operate any
faster or produce greater quantities of water.
Initially allow approximately a one-minute delay from when the pressure-dispensing pad is pushed until the
water is dispensed. While the tank is filling, no water sign will appear.
Dispense at least 8 to 10 litres (8 to 10 quarts) of water through the system, stopping intermittently to ensure
that air in the tank is flushed out. Failure to do so will result in excessive dripping from the dispenser.
9.4
Water Filter and Cartridge
The product is supplied with a water filter and cartridge. It is recommended that the filter be mounted in a
vertical position. Where the filter is positioned is up to the customer.
The replacement icon will appear and blink when the filter needs to be replaced. This is approximately every
6 months.
Summary of Contents for 635 Active Smart
