background image

517672 
 

 

INTRODUCTION 

The service manual covers the implementation of electronic control to Vertical Freezers. 

1.1 

Electronics 

Changes to the single temperature models are that an electronic module has replaced the defrost 
timer and relay.  A variable resistor replaces the thermostat. 
 
With the introduction of the electronic module, some of the current functions of the product will also 
change.  These will be covered under the appropriate headings. 
 
The  operational  component  such  as  the  evaporator  has  also  changed  from  the  corrugated  type 
evaporator to the new Showa fin on tube evaporator.  The condenser and cabinet do not change. 
 

1.2 

Product Specification 

1.2.1 

Compressors 

Product Model 

Compressor Part Number 

Refrigerant Charge 

E373/450

 

207119

 

100 grams R134a 

 

1.2.2 

Compressor Specification 

Brand 

Matsushita 

Model 

SF48C91RAW5 

Part Number 

207116 

Volts 

230/240 

Hertz 

50 

Nominal BTU 

470 

Output Watts 

138 

Run Current (Amps) 

0.50 

Start Resistance (Ohms) 

28.50 

Run Resistance  (Ohms) 

18.20 

Relay 

F&P Electronic 

Overload Part Number 

 

Run Capacitor Part Number 

207164 

 

1.3 

Condenser Layout 

The  new  compressors  have  no  oil  cooler  lines;  therefore  the  re-routing  of  the  condenser  is  as 
follows: 
Discharge  line  from  the  compressors  runs  directly  to  the  waste  water  tray  and  then  into  the 
condenser on the back panel.  From the back panel it enters the LH side condenser (viewed from 
the rear), through the cross rail heater (if applicable) then into the RH side condenser, then into the 
filter dryer.  The remaining layout remains unchanged. 

Summary of Contents for E373















Reviews: