background image

1,5V

LR20 (“D”)

+

_

6

Battery Installation

1

2

Hint: 

We recommend using an 

alkaline 

battery 

for longer battery life.

Battery Compartment

Pad Bottom Pocket

• Remove the pad bottom pocket from the footrest.

• Insert a coin into the battery compartment door and pry the

battery compartment door off. 

• Insert one LR20 (“D”) 

alkaline

battery into the

battery compartment.  

• Replace the battery compartment door.
• Pull and fit the pad seat bottom pocket around the soothing

unit and footrest.

Shown Actual Size

Battery Safety Information

Batteries may leak fluids that can cause a chemical burn injury 
or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different

types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always

remove exhausted batteries from the product. Dispose of 
batteries safely. Do not dispose of batteries in a fire. 
The batteries may explode or leak.

• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type 

as recommended.

• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product 

before charging.

• If removeable, rechargeable batteries are used, they are 

only to be charged under adult supervision.

Summary of Contents for H5124









Reviews: