background image

Soother Battery Compartment 

7

Mobile and Sounds Battery Compartment 

• Locate the electronic unit on the frame. You will see that 

there are two battery compartments. The smaller battery 
compartment   powers the soother; the larger battery com-
partment 

 powers the mobile/sounds.

• First, loosen the screw in the soother battery compart-

ment. Remove the battery compartment door. Insert one “D” 
(LR20) 

alkaline

 battery, as indicated inside the battery com-

partment. Replace the battery compartment door and tighten 
the screw.

• Next, loosen the screws in the mobile battery compartment 

door. Insert three “C” (LR14) 

alkaline

 batteries, as indicated 

inside the battery compartment. Replace the battery com-
partment door and tighten the screws.

IMPORTANT!

 Low battery power in the product may cause 

it to operate erratically (no sounds/no movement/no vibra-
tions) and the product may not turn off. If this should happen, 
remove and discard all batteries and replace with new, 

alkaline

 batteries.

Battery Installation

Hint:

 We recommend the use of 

alkaline

 batteries

for longer battery life.

"D" (LR20)

1.5 Volt – Soother

"C" (LR14)

1.5 Volt x 3 – Mobile/Sounds

In exceptional circumstances, batteries may leak 
fluids that can cause a chemical burn injury or ruin 
your product. To avoid battery leakage: 

• Do not mix old and new batteries or batteries of different 

types: alkaline, standard (carbon-zinc) or rechargeable 
(nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always 

remove exhausted batteries from the product. Dispose of 
batteries safely. Do not dispose of product in a fire. The bat-
teries inside may explode or leak.

• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type 

as recommended.

• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product 

before charging.

• If removeable, rechargeable batteries are used, they are 

only to be charged under adult supervision.

Battery Safety Information

•  Protect the environment by not disposing of this 

product with household waste (2002/96/EC). 
Check your local authority for recycling advice 
and facilities (Europe only).

Summary of Contents for J6986













Reviews: