background image

Battery Charging

• Plug the charger connector into the battery 

.

• Plug the charger into a standard 120 volt wall outlet 

.

Note: If power flow to the wall outlet is controlled by a
switch, make sure the switch is “ON”.
• Before first-time use, charge the battery for at least 18

hours. Never charge the battery longer than 30 hours.

• Recharge the battery for at least 14 hours after each 

use of your vehicle. Do not charge the battery longer 
than 30 hours.

• Once the battery is charged, pull firmly on the charger

connector to disconnect it from the battery. Unplug the
charger from the wall outlet. The battery is now ready to
be installed in your vehicle. Please see the Battery
Installation section on page 16 for detailed instructions on
installing your battery. If your battery is already installed in
your vehicle, simply re-connect the motor harness
connector to the battery.

11

2

11

1

Battery

Charger
Connector

Important Notes

• Your new battery must be charged for at least 

18 hours before you use it in your vehicle for the
first time.

• We recommend that you start charging your battery

before beginning assembly of your new vehicle. 

• You do not need to remove the battery from your 

vehicle to recharge it.

• The battery must be upright while charging.

• The charger is not a toy.

• Do not short circuit the battery.

• Before charging the battery, examine the battery case

for cracks and other damage which may cause sulfuric
acid (electrolyte) to leak during the charging process. If
damage is detected, do not charge the battery or use it
in your vehicle. Battery acid is very corrosive and can
cause severe damage to surfaces it contacts. 

• Do not charge the battery on a surface (such as kitchen

counter tops) which could be damaged by the acid
contained inside the battery. Take precautions to protect
the surface on which you charge your battery. 

• Use only a Power Wheels

®

12 volt charger with type

“12V” connector (120 VAC 60 Hz 28W with an output 
of 12 VDC 1200mA) to charge your Power Wheels

®

rechargeable 12 volt battery.

• If your battery is old and will not accept a charge, do not

leave it in the vehicle. Always remove a dead battery
from the vehicle.

11

1

11

2

8

Summary of Contents for Power Wheels C7478

























Reviews: