background image

8

NOTE:  if you are working 

in shallow water, you may 

want to strap the control 

housing on your chest in a 

heavy plastic bag, and seal 

it tightly around the cable.

29

To remove the control housing from the 

stem, grasp the top of the control box firmly 

and pull it directly toward the armrest while 

holding the GoldBug2 handle. 

Figure 4.

  

Your  GoldBug2 is lightweight and well balanced; however, if you 

are going to be swinging it for more than a few hours, you may want 

to “hip-mount” it by removing the control box and strapping it to your 

waist. Follow this procedure:

 

1

Disconnect  the  cable  from  the 

control  housing  and  unwind  all 

but  the  last  12-inches  or  so  from 

the  stem.  Secure  the  lower  end 

of the cable with a velcro strap at 

least  12-inches  up  from  the  coil. 

CAUTION: MAKE SURE THAT YOU 

HAVE ENOUGH SLACK AT THE 

SEARCHCOIL 

2

Slide  the  control  housing  off  the 

handle by holding the hand grip with 

one hand and pulling the housing 

toward you with the other hand. 

3

Reconnect the cable to the control 

housing. 

NOTE:  It is especially 

important that the cable connector be 

installed tightly to prevent false signals 

during hip-mount use. Hand tighten only: 

Never use tools to tighten the connector

4

Put your belt through the slots on 

the underside of the housing. 

5

Left  handers  should  wear  the 

housing on their right hip and right 
handers on their left hip.

The GoldBug2 control housing can be 

hip-mounted to reduce weight on the stem 

and create nearly effortless  hunting. Belt 

loops are provided on the underside of the 

control housing.

Figure 3.

HIP-MOUNTING

LET’S PRESERVE OUR TREASURED SPORT!

Laws governing the use of metal detectors are becoming more and 

more common. In many countries, the use of metal detectors is 

illegal or severely restricted. Do not let this happen in your area. 

•  Always check Federal, State, County and local laws before 

searching.

•  Respect private property and do not enter private property 

without the owner’s permission.

•  Take care to refill all holes and leave no damage.

•  Remove and dispose of any and all trash and litter found.

•  Appreciate and protect our inheritance of natural resources, 

wildlife and private property.

•  Act as an ambassador for the hobby; use thoughtfulness, 

consideration and courtesy at all times.

•  Never destroy historical or archaeological treasures.

•  All treasure hunters may be judged by the example you set; always 

conduct yourself with courtesy and consideration of others

.

Using headphones (not included) improves battery life, and allows 

you to hear subtle changes in the sound more clearly, particularly 

if searching in a noisy location. For safety reasons, do not use 

headphones near traffic or where other dangers are present. This 

device is to be used with interconnecting cables/headphone cables 

shorter than three meters.

USING HEADPHONES

TREASURE HUNTER’S CODE OF ETHICS

Summary of Contents for Gold Bug-2





































Reviews: