AUTOREPEAT RECORDING
Autorepeat Recording
The same tape can be recorded over many times.
œ
Follow the Before starting steps, under “NORMAL
RECORDING”.
1
Set the REPEAT REC switch to the “ON” position.
ø
The REPEAT indicator will light.
2
Press the MENU button until the (SET UP 3) menu is
displayed.
ø
The “ALARM MODE” setting is flashing.
@@@@@@@<SET@UP@3>
öALARM@MODE@@@@@@@Y1
öALARM@DURATION@@@20S
öVERTICAL@SYNC@@@@Y
öEXT@TIME@ADJ.@@@@01:00
öTAPE@IN@MODE@@@@@STOP
öTAPE@END@MODE@@@@R1
öTAPE@END@OUT@@@@@-3M
öCLOG@DETECT.@@@@@Y
öSERIES@REC@IN@@@@N
öRS-232C@@@@@@@@@@19200
3
Turn the JOG dial, until the “TAPE END MODE”
setting is flashing.
4
Turn the SHUTTLE ring to set to “R 1” or “R 2”. (See
“Setting the Mode at the End of the Tape”)
5
Press the SEARCH button to save the setting.
ø
The setting procedure is now completed.
6
Press the REC/PLAY SPEED
l
(or
j
) button to set
the recording speed mode.
7
Press the REC button.
ø
Recording will start. When the tape end is
reached, the VCR will rewind it to the beginning,
and recording will resume.
ø
When the end of the tape is reached, a buzzer
will be heard (if in the (SETUP 2) menu, in the
BUZZER section TAPE END is set to “Y”) and
“OFF” will be displayed until the rewinding
operation starts.
NOTES:
œ
If during autorepeat recording there is an alarm trigger,
“AL” is displayed on the digital display and alarm
recording will take place. (Please refer to page 17,
“ALARM RECORDING”.)
œ
If the “TAPE END MODE” setting is R 1, the REPEAT
indicator will go off if there is an alarm trigger. The
recording will continue to the end of the tape then it will
be rewound to the beginning and stop. “OFF” will be
displayed on the digital display. To turn off the buzzer
(if in the (SETUP 2) menu, in the BUZZER section
TAPE END is set to “Y”) and the “OFF” display, press
the STOP, EJECT or PLAY button, or turn the
SHUTTLE ring.
œ
If “AL” is displayed on the digital display and the “TAPE
END MODE” setting is R1, autorepeat recording is not
possible.
Setting the Mode at the End of the Tape
In the (SET UP 3) menu, you can set the mode of the
VCR mode when the tape reaches the end during
recording.
1
Press the MENU button until the (SET UP 3) menu is
displayed.
@@@@@@@<SET@UP@3>
öALARM@MODE@@@@@@@Y1
öALARM@DURATION@@@20S
öVERTICAL@SYNC@@@@Y
öEXT@TIME@ADJ.@@@@01:00
öTAPE@IN@MODE@@@@@STOP
öTAPE@END@MODE@@@@REW
öTAPE@END@OUT@@@@@-3M
öCLOG@DETECT.@@@@@Y
öSERIES@REC@IN@@@@N
öRS-232C@@@@@@@@@@19200
2
Turn the JOG dial, until the “TAPE END MODE”
setting is flashing.
3
Turn the SHUTTLE ring, to set the desired mode.
œ
Setting when the REPEAT REC switch is set to the
“OFF” position.
REW. . . . . . . Rewinds the tape to the beginning,
then goes to stop mode
STOP . . . . . . Goes to stop mode
EJECT . . . . . The cassette is ejected
œ
Setting when the REPEAT REC switch is set to the
“ON” position.
R1. . . . . . . . . Autorepeat recording mode is
automatically canceled if there was
an alarm trigger
R2. . . . . . . . . Autorepeat recording mode is
active even if there was an alarm
trigger
4
Press the SEARCH button to save the setting.
RC4QR/U3 (SRT-7072 GB) Tue. June, 29/1999
16
English
