background image

- 21 -

Using salt damage inhibitor SALT-AWAY included in the FIX maintenance kit, sold 
separately, is even more effective.

1. Submerge the light body into fresh water for about 10-20 minutes before opening the light head 

after use. Also press the Power Button/Light Output Adjustment Button and Light Output 
Adjustment Button in fresh water several times and wash off the salt deposits around buttons.

2.After removing from fresh water, rinse with slow flowing running water. Never use high pressure 

water from one direction as it may cause water intrusion.

3.After rinsing, wipe off remaining water with a soft dry cloth. Do not dry in direct sunlight or dry 

with a dryer or stove as it may cause failure, deformation or damage.

4.After use, lightly coat the O-ring with silicon grease and store. Replacing with a new O-ring once 

a year is recommended.

5. For long time storage, avoid areas of extreme high temperature and humidity, direct sunlight or 

extreme cold temperature.

6. Never use any organic solvents such as alcohol, benzene or thinner or neutral detergents as it 

may cause deformation or damage.

The circuit board location of this product is waterproof to minimize the damage even in case of 
water intrusion occurring inside the light body. The battery is also “drip-proof”. In case of water 
intrusion, however, immediately stop using this product and remove any residual water inside of 
the light and the battery. Do not put the battery back in the light body and store it separately. If 
there is some water remaining inside, it may cause electric shock or damage to the circuit board 
therefore never use it after water intrusion and contact Fisheye or your local retailer for service.

Care and Storage

In case of internal water contact

Regular overhaul is recommended once every 1-2 years, regardless of the frequency of use of 
this product. Waterproof O-rings that cannot be exchanged by customers are used inside of the 
product. Please ask Fisheye Customer Service for overhaul after a certain period of time to 
exchange and maintain these to prevent accidents and extend the life of the product.

Recommended Service

After use in salt water, if salt deposits are allowed to remain and dry in small gaps, salt 
crystals will form and will not subsequently dissolve. Make sure to submerge in fresh water 
to wash off the salt deposits as these salt crystals may occasionally push up the O-ring and 
cause water intrusion.

CAUTION

NOTE

Summary of Contents for FIX NEO Mini 800SS

























Reviews: