background image

 

 

Before You Start 

 

IMPORTANT! Please read all instructions carefully before using this product.  Retain this 
manual for future reference. The  specifications  of  this  product  may  vary  slightly  from  the 
illustrations  and  are  subject  to  change without notice. 

 

IMPORTANT SAFETY NOTICE 

 
Note  the  following  precautions  before  assembling  and  operating  the 
machine. 
1. Once fully assembled, please check that all hardware parts such as bolts, 
nuts and washers are positioned and secured firmly.   
2. Please check regularly that the safety chain guard that protects the moving 
parts of the machine is secured and in good order. 
3. Please always check the seat  post, seat slider; pedals and handlebar are 
secured firmly before getting on the bike.   
4. To lubricate all moving parts annually is recommended.   
5. Do not wear loose clothing to avoid entangling in any moving parts.   
6. Do not remove feet from the pedals while they are in motion.   
7. Always wear shoes when using the machine.   
8.  Dry  the  bike  after  each  use  to  remove  sweat  and  moisture.  Wipe  the 
machine  with  a  damp  cloth,  water  and  mild  soap.  Do  not  use  a 
petroleum-based  solvent  to  clean the  machine  in  order  not  to  damage the 
finish. 
9.  Please  keep  children  away  from  the  bike  while  it  is  in  use.  Do  not  allow 
children to use the bike. This bike is designed for adults, not children.   
10. Do not dismount the bike until the pedals have stopped completely.   
11.  Stop  exercise  immediately  in  case  of  nausea,  shortness  of  breath,  faint, 
headache, pain, tightness in your chest or any discomfort.   
12. Do not place fingers or any other objects into the moving parts of the bike.   
13.  Prior  to  any  exercise,  consult  with  your  physician  first  to  establish  the 
exercise frequency, time and intensity appropriate for your particular age and 
condition.   
14.  After  exercising,  please  pull  down  the  tension  controller  to  increase 
resistance so that the pedals will not rotate freely and possibly hurt someone. 

15. Maximum user’s weight is 1

35KGS. 

 
 
 

Summary of Contents for CYCLO 300












Reviews: