background image

DO NOT TOUCH BURNERS, BURNER 
GRATES, OR INTERIOR SURFACE 
OF OVEN. 

These surfaces may be hot 

enough to burn even though they appear to 
be cool. During and immediately after use 
do not touch or let clothing or other 
flammable materials contact any hot 
surfaces or any interior area of the oven. 
Allow sufficient time for cooling.

 

 

Potentially hot surfaces include the cooking 
surface and areas facing the cooking surface, 
oven vent opening, and crevices around the 
oven door. 

 

Remember: The inside surface of the oven 
door may be hot when the door is opened. 
 

 

 

Oven 

 

Do not bake in a gas oven or use a broiler 
pan with excess grease buildup.

 Be careful 

when handling the broiler pan, especially 
when hot. Grease left in the pan can catch 
fire if the oven is used without removing the 
grease from the broiler pan. Keep oven free 
from grease buildup. 

 

Never use ammonia in an oven that is 
warmer than room temperature and 
always have direct ventilation. 

 

Stand away from the range when opening 
the oven door.

 Hot air or rising steam can 

cause burns to hands, face, and/or eyes. 

 

WARNING!!! 

Never cover any slots, holes, or passages 
in the oven bottom or cover an entire rack 
with aluminum foil or other materials.

 

Doing so blocks air flow through the oven 
and may cause carbon monoxide poisoning. 
Aluminum foil linings may also trap heat, 
causing a fire hazard. 

 

When replacing an oven light bulb, be 
sure the oven is cool. Disconnect power to 
the range, and use a dry cloth to handle 
the bulb. 

 

Do not heat unopened food containers 
in the oven. 

Pressure could build up and 

the container could burst causing injury. 

 

Place oven rack in desired position 
while oven is cool.

 If rack must be 

handled when hot, use a pot holder. 
Pulling out the oven rack to the stop 
position is a convenience in lifting 
heavy goods. It is also a precaution 
against burns from touching hot surfaces 
of the door or oven walls. 

 

When using cooking or roasting bags 
in the oven, follow the manufacturer’s 
directions. 

 

Do not use your oven to dry 
newspapers or any other flammable 
materials. 

 

Surface Cooking 

 

Use proper pan size. Select utensils 
with flat bottoms large enough to 
cover the burner. 

The use of 

undersized utensils in which flame 
wraps the side of the utensil does not 
heat the contents faster; it only scorches 
the outside of the pot or pan, making 
clean up more difficult. Adjust the top 
burner knob to select a flame size to 
cover just the bottom of the pan or pot. 

 

Surface areas near burners may 
become hot enough to cause burns.

 

During and immediately after use, do 
not touch areas near burners until they 
have had sufficient time to cool. 

 

Never leave top burners on and 
unattended. Boil-overs cause smoking 
and greasy spill-overs may catch on 
fire. 

 

Do not use aluminum foil to line 
burner pans or inside oven except as 
described in this manual. 

Misuse could 

result in fire hazard or damage to the 
range.  

 

Only certain types of glass, 
glass/ceramic earthenware, or other 
glazed containers are suitable for range 
top use. Others may break because of 
the sudden change in temperature. 
Always refer to specific cookware 
instructions.  

Always turn utensil handles to the 
side or back of the range to avoid 
accidental bumping and to keep 
out of reach of children. 
 

 

 

Always turn surface burner to 
OFF before removing cookware.

  

 

To avoid the possibility of a burn 
always make certain that the 
controls for all top burners are in 
OFF position and all burner pans 
are cool before attempting to 
remove the grates, burner caps, 
burner pans, or burners. 

 

Do not put removable surface 
burners in a dishwasher. 

 

Be attentive to frying foods at all 
temperatures. 

 

Foods for frying should be as dry 
as possible. 

Frost or ice on frozen 

foods or moisture on fresh foods can 
cause hot fat or oil to bubble over 
sides of pan very quickly.  

 

Use only enough fat or oil for 
effective shallow or deep frying.

 

Filling the pan with excess fat can 
cause spill-overs when food is 
added. If a combination of oils or 
fats will be used in frying, stir 
together before heating or as fats 
melt. Always heat fat slowly and 
monitor as it heats. 

 

Use a deep fat thermometer 
whenever possible to prevent 
overheating fat or oil beyond the 
smoking point. 

 

EACH HOUSEHOLD SHOULD 
HAVE AN APPROPRIATE 
FIRE EXTINGUISHER FOR 
USE IN THE EVENT OF A 
HOUSE FIRE. 

11 

Summary of Contents for TPN335-BGW





































Reviews: