background image

INSTALLATION: 

The installation of this heater for use with natural gas shall conform with local codes or, 
in the absence of codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54 and 
the Natural Gas and Propane Installation Code, CSA B149.1. 
 
The installation of this heater for use with propane tank or cylinder shall conform with 
Local codes or, in the absence of local codes, with the Standard for the Storage and 
Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and the Natural Gas and 
Propane Installation Code, CSA B149. 
 
This heater must be located at least 10ft (3m) from any propane gas cylinder. This 
heater shall not be directed toward any propane gas container within 20ft (6m). 
 

CLEARANCE TO COMBUSTIBLES: 
 

F-1500T  

 

TOP: 4 ft  

   FRONT: 16 ft  

SIDES: 2 ft        REAR: 2 ft 

 

 
CONNECTING THE CYLINDER: 
 

If cylinders are used to supply the heater, no cylinders smaller than 100lb capacity shall 
be used. These cylinders must supply a vapor withdrawal only. 
 
1.  

All cylinder connections must be made using a wrench to tighten the POL     
fitting. 

 
2.  

Be sure that the cylinder valve is in the closed position when connection 
or disconnecting the cylinder. 
 

3.  

A soap and water solution must be applied to all connections in order to leak 
check the system. 
 

The gas must be turned off at the propane supply cylinder(s) when the heater is not in 
use. When the heater is to be stored indoors, the connection between the propane 
supply cylinder(s) and the heater must be disconnected and the cylinders removed from 
the heater and stored in accordance with Standard for the Storage and Handling or 
Liquefied Petroleum Gases, ANSI/NFPA 58 and CSA B149.1, Natural Gas and Propane 
Installation Code. 
 

PIPING: 

This heater must be installed by a qualified gas technician following 

local codes published by the authority having jurisdiction. Sizing of 
supply piping must be determined using the length of pipe run as 
well as total btuh rating of the appliance(s). Appropriate piping 
tables must be used to determine size of supply piping dependant 
on the length of run from source. 

 

Summary of Contents for F-1000T















Reviews: