FL
AIR
MO ApS
–
Lundeborgvej 3
–
DK-9220 Aalborg
–
Denmark
Phone: +45 53717220 Web: www.flairmo.dk - E-mail: info@flairmo.dk
Important - read this first!
Please read the following information and operating instructions
included with this product before use. This information is for your safety
and it is important that you follow these instructions. It will also help
prevent damage to the product. Failure to operate the unit in
accordance with the instructions or using unauthorized spare parts can
cause damage to the unit and could cause serious injury.
CAUTION: To reduce risk of electric shock
• Only authorized service agents should carry out service. Removing
parts or attempting repairs can create an electric shock. Refer all
servicing to qualified service agents.
• If this unit is supplied with a three-pin plug, connect with a properly
earthed outlet only.
WARNING: To reduce risk of electrocution
• Do not use this unit with electrical voltages other than stated on the
rating plate.
• Always unplug this unit immediately after use, and store in a dry place
• Do not use this product in or near liquid or where it can fall or be
pulled into water or other liquids.
• Do not reach for this product if it has fallen into liquid Unplug
immediately.
• This unit is not weatherproof. Never operate outdoors in the rain or in
a wet area.
DANGER: To reduce risk of explosion or fire
• Do not use this product in or near explosive atmospheres or where
aerosol products are being used.
• Do not pump any other gases other than atmospheric air.
• Do not pump combustible liquids or vapours with this product.
• Do not use this unit near naked flames.
CAUTION: To prevent injury
• Compressed air can be dangerous; do not direct airflow at your body.
• Always keep the compressor out of reach of children.
• Never operate this product if it has a damaged power lead or plug, if
it has been dropped or damaged, or if it has fallen into water. Return
the product to a service centre for examination and repair.
• Keep the electrical cable away from heat.
• Never restrict fans. Ensure all openings are kept free of restriction.
• Never insert fingers or any other objects into fans.
• This unit is thermally protected and can automatically restart when
the overload resets.
• Wear safety glasses when servicing the compressor.
• Use only in well ventilated areas.
• Do not use any items not recommended for use with compressed air.
• The surface of the compressor can get hot. Do not touch compressor
motor during operation.
• Failure to observe the above safety precautions could result in severe
bodily injury, including death in extreme cases.
.
IMPORTANT: General directions for use
• Protect compressor against rain, moisture, frost and dust.
• The OF300 series is constructed and approved for a max. pressure
as indicated under Technical data
• Do not operate compressor at ambient temperatures exceeding
40°C/104°F or falling below 0°C/32°F.
• If the supply lead on the compressor is defective, an authorized
FLAIRMO distributor or other qualified personnel must carry out the
repair.
Warranty
Provided that the operational instructions have been carried out,
your FLAIRMO compressor is guaranteed against faulty material or
workmanship for 2 years.
The guarantee does not cover damage caused by violence, misuse,
incorrect repairs or use of unoriginal spare parts.
Costs of transportation of parts/equipment are not covered by the
guarantee.
In Scandinavia it is NL-92 Terms & Conditions that applies.
FLAIRMO ApS reserves the right to change technical
specifications/constructions.
Contents of box (motor only)
Your new compressor/vacuum pump should be delivered in
a clean and undamaged box. If not, contact your distributor
immediately. The box should contain the following:
Installation (motor only)
Your FLAIRMO motor is very easy to operate. Observe the
following simple instructions and you will get many years’
service from your motor.
• Visually inspect unit for shipping damage, contact your
supplier immediately if you think the unit may have been
damaged.
Warning!
To avoid the risk of electric shock, do not install the
compressor in areas where it may get in contact with
water or other liquids. In which case protection is required.
• Remove the plastic protection from the outlets.
• Use only pressure pipes tolerating
a constant temperature of min. 1500C. Ensure that the
pressure pipes have a sufficient internal diameter to avoid
pressure loss in the system. Check for leaks.
• Mount the supplied feet on the compressor
• It is important that the compressor is mounted vertically to avoid
damage to the rubber feet. If the compressor is to be mounted in
another position, please contact FLAIRMO for further information.
• Sufficient cooling from the surroundings is important. Place the motor
in a dustfree, dry and cool, yet frostfree, room. Do not install in a closed
cupboard, unless adequate openings for ventilation are available on top
and bottom (minimum 500 cm²/77.5 in² each). If the motor is placed
under a table, a minimum of 10 cm/3 inch free height must be available
above the motor (fig. 3), or an opening of Ø30cm/11.8 inches,
corresponding to the top of the motor, may be cut in the table.
Ensure that the motor stands firmly on the floor.
• The intake air may be supplied from another place (for
instance outside).
Nipple and hose should then be mounted in the thread on the top of the
intake filter, and led to the external air source.
Ensure that hoses for the intake are sufficient to avoid
performance loss.
Electrical installation (motor only)
Warning!
Incorrect electrical connection may result in electric
shock. The electrical connection must be carried out
in accordance with local electrical regulations and by
qualified electrical engineers.
Note!
Earthing of all AC models must be ensured during
installation. The capacitor must be earthed, as failure to do
so may cause electric shock when touched. Plug the motor
into an earthed socket of nominal voltage and ensure that
fusing is adequate, see Technical Specifications
AC models
• For electrical connection, refer to page 7
• Check motor plate for frequency, voltage and capacitor and
ensure that it corresponds to the voltage and frequency
used for the motor. The voltage stated on the motor plate:
120/240V (/) means that the motor can operate at 120V or
240V, but this requires recoupling of the internal wiring from
the electrical motor (see the electrical diagrams). 220-230V
(-) means that the motor may operate within the range of
220V to 230V without recoupling of the internal wiring.
DC models
• For electrical connection, refer to page 7
• During installation of the DC motor, check the motor plate
for the direction of rotation as it is important that the "+" and
"-" poles are connected in a correct way (fig. 5). Otherwise,
Information
Please note that you can find the pictures and
figures we are referring to on page 6-9.
