FläktGroup Semco NEUTON, Owner'S Manual

23

OWNER’S MANUAL

NEUTON™

Name

Description

Type

Object ID

Device ID

Object Name

Exp:-

Num

I/O Type

zone 4 enthalpy

zone enthalpy calculated based on 

the temperature and RH input from 

(selectable) the Zone Sensor or BAS 

comm input

BAV

AV:437

DEV:2402

zone_4_enth_1

zone 4 grains

zone grains calculated based on 

the temperature and RH input from 

(selectable) the Zone Sensor or BAS 

comm input

BAV

AV:438

DEV:2402

zone_4_grains_1

zone 5 dewpoint

zone dewpoint calculated based on 

the temperature and RH input from 

(selectable) the Zone Sensor or BAS 

comm input

BAV

AV:539

DEV:2402

zone_5_dewpt_1

zone 5 enthalpy

zone enthalpy calculated based on 

the temperature and RH input from 

(selectable) the Zone Sensor or BAS 

comm input

BAV

AV:540

DEV:2402

zone_5_enth_1

zone 5 grains

zone grains calculated based on 

the temperature and RH input from 

(selectable) the Zone Sensor or BAS 

comm input

BAV

AV:541

DEV:2402

zone_5_grains_1

Zone RH 1

BAV

AV:711

DEV:2402

zone_rh_1_1

Zone RH 2

BAV

AV:712

DEV:2402

zone_rh_2_1

Zone RH 3

BAV

Zone RH 4

BAV

AV:714

DEV:2402

zone_rh_4_1

Zone RH 5

BAV

AV:715

DEV:2402

zone_rh_5_1

Zone Temp 1

BAV

AV:701

DEV:2402

zone_temp_1_1

Zone Temp 2

BAV

AV:702

DEV:2402

zone_temp_2_1

Zone Temp 3

BAV

AV:703

DEV:2402

zone_temp_3_1

Zone Temp 4

BAV

AV:704

DEV:2402

zone_tmp_4_1

Zone Temp 5

BAV

AV:705

DEV:2402

zone_tmp_5_1

allow co2 

override

If this point is ON, and if the signal if 

valid from the Zone Sensor CO2 sensor, 

then if the space CO2 is greater than the 

"CO2 force OCC mode setpoint", AV:3, 

then occupied mode is forced .

BBV

BV:1

DEV:2402

allow_co2_

override_1

CO2 option

This point must be set to ON if CO2 is 

included in the sensor

BBV

BV:2

DEV:2402

co2_opt_1

CO2 Override 

Status

If CO2 option BV:2 is ON and conditions 

are met, this status point will be on and 

the mode will be Occupied .

BBV

BV:3

DEV:2402

co2_override_1

Cooling Mode 

Status

Cooling Mode Status - if Heating Mode 

has been off for 1 minute, and shutdown 

mode is not active, and heat is called by 

the thermostat, then Cooling Mode Status 

is ON .

BBV

BV:5

DEV:2402

clg_status_1

Heating Mode 

Status

Heating Mode Status - if Cooling Mode 

has been off for 1 minute, and shutdown 

mode is not active, and heat is called 

by the thermostat, then Heating Mode 

Status is ON .

BBV

BV:6

DEV:2402

htg_status_1

OCC command 

from BAS

If this point is ON, the controller uses the 

occupied setpoints

BBV

BV:7

DEV:2402

occupied_bas_1