16
TRANSLATION OF THE ORIGINAL INSTRUCTIONS (Keep for future reference)
Document Code
Rev.
Date saved
Date printed
U400 INSTRUCTIONS
01
02/10/2015
02/10/2015
EN
2. INSTALLATION
2.1. STORAGE
The machine, intended for indoor installation must be stored, if necessary, in well ventilated storage facilities and protected from dust.
?<*@<*!&%!%!#&&%?&#*"#$&&%*%?%!&#*&%#**#%&
**"#%%?!#$?&'$%%%?;<#%&#"%$%<>%?##&<"%$%@"#\#%%?%!<"#%$?%"@&%
oxidation caused by weather conditions.
In the case of prolonged inactivity the machine must be stored with all necessary precautions taken based on the location and expected
storage times:
1. Store the machine in an enclosed place.
2. Protect the machine from impact and stress.
3. Protect the machine from humidity and excessive temperature differences (refer to the table below).
4. Do not allow corrosive substances to come into contact with the machine.
5. Check that the pack has not been damaged and that it is perfectly dry.
"$$#**\[%?!#$?&&<#?""&$&%#&[%?%##!%'$@<#&<"%$%<##&%<$%>#%?
including rain, snow and hail, and it must be accessible exclusively to authorized personnel.
The machine is protected in such a way as to withstand the temperatures, humidity and vibration levels typically associated with transport
and storage.
Ambient
temperature
Storing
temperature
Relative humidity
Vibrations
Atmospheric
pressure
-25 ÷ +40°C - 13 ÷ 104°F
-25 ÷ +55°C - 13 ÷ 131°F
0 ÷ +55 °C / 32 ÷ 131°F
100% at a temperature of +25°C / 77°F
Lower than 50% at a temperature of +40°C / 104°F
Lower than 90% at a temperature of +20°C / 68°F
5.9 m/s2 (0.6G) or higher
900 mbar or more
Avoid places where
there may be
unexpected changes
in temperature
which could lead
to the formation of
condensate or freezing.
Storage temperature is construed as a short-term value, e.g. during transportation. Condensation or freezing normally occurs in sites
'$%%&$#&%%!"#%;$&@&*#%@?!<%\&$?$&<%&#**>%?&%?@#*?>&&%?%#'*[*$#%&
'$%%&$#&%%!"#%$?#&?*<'#@<<
2.2.
CHECKS ON RECEPTION
NOTES
It is essential to check the packs at the time of arrival and in the precise moment in which they are received. The check is performed
in two stages for each pack received to avoid misunderstandings with the shipping agent.
Administrative check
1. Crate number and number of packs.
2. Weight and size
3. Correspondence of information on shipping document with the material effectively delivered (description, serial number, etc). The
%$?&$#*<#%#@&&%?!#$?&<&%$#%&"*#%!%$"&<>%?%?<#%@&&%?%$?&$#*<#%#""*<
4. Check correspondence between shipping document data and the order.
Technical check
1. Condition and intactness of packaging.
2. Check that the packaging shows no signs of visible damage caused during transport and handling operations.
All the above checks must be performed by inspection in the presence of the shipping agent’s delivery person. If any damage is noted
or the supply is incomplete or incorrect, inform the manufacturer’s sales department immediately.
NOTES
In relation to the above prescriptions, the manufacturer informs the user that in compliance with current international and national
rulings, goods are always shipped at the risk and responsibility of the purchaser and, unless otherwise stated in writing at the time
