ALC 3/360-G/R 10.8
19
Horizontal laser line control
■
Press the key “ horizontal laser line (3) ” to
turn on or turn off the horizontal laser line.
■
The horizontal laser line H is a 360°
horizontal laser (Fig.F).
Vertical laser lines control
■
Press the key “ vertical laser line (4) ” to
turn on or turn off both groups of the
vertical laser lines V1V2 and V3V4 (Fig.G).
Auto-leveling mode
NOTE
The indicator light (2) will be red flashing with
buzzer warning and the laser will keep flashing,
while the tool cannot finish auto-leveling.
If auto-leveling is always not possible, it
means the surface on which the tool stands
deviates by more than auto-leveling range 4°
from the horizontal plane. Please place the
tool in a position closed to level ( ≤4° from
the horizontal plane) .
■
Position the measuring tool on a level and
firm support, attach to the tripod.
■
Push the locking rotary knob (7) to the “ ”
position.
NOTE
After switching on, the levelling function
automatically compensates irregularities
within the self-levelling range of ±4°.The
levelling is finished as soon as the laser
beams do not move any more.
Vertical laser line
When the horizontal laser line is lit up, press
the key “vertical laser line (4)” to control the
vertical lines V1V2 and V3V4 to light up or
just to the side, or off at the same time.
When the horizontal laser line is not lit
up, press the key “vertical laser line (4)” to
control the vertical lines V1V2 and V3V4
to light up or only on the side, but the two
groups of vertical laser lines cannot be
completely turned off at the same time.
Horizontal laser line
Only when at least 1 group of vertical
laser lines is lit up, the horizontal laser line
can be turned off.
Work without auto-leveling mode
(Lock mode)
This mode always be used as adjust or mark
the line exceeds 4° from the horizontal
plane. For example, set up the stair rail.
NOTE
■
Pay attention that the tool will not come
out any warning sound in this mode even
it exceeds the auto-leveling range 4°.
This mode cannot be used to perform
horizontal or vertical leveling.
■
Keep the locking rotary knob in “ ”
position, press the key “ horizontal laser
line (3) ” or “ vertical laser line (4) ” for a
long time to open the corresponding laser,
the tool will work in lock mode.
■
Press the key “ horizontal laser line (3) ” or
“ vertical laser line (4) ” to select a specific
laser projection mode.
■
The indicator light (2) will always be red to
caution the function mode;
■
Position the tool naturally at the desired
angle and then go on working with the
laser to proceed to the next step.
■
After the laser is all off, the tool shuts down
simultaneously.
Outdoor mode
■
Press the switch button (6) for a while to
select outdoor mode. The laser will dim
a little while in outdoor mode, which is
normal.
■
Please use the tool with a receiver (sold
separately) while in outdoor mode.
Indicator light
Indoor mode
■
Default indoor mode after starting up the
tool.
■
At this moment, the indicator light (5)
comes on two on the left
■
Short press switch button (6) to select
different brightness.
Outdoor mode
Long press the switch button (6), and then the
indicator light (5) will only light up one on the
far left and it will be flashing, prompting to
enter the outdoor mode.
Summary of Contents for ALC 3/360-G/R 10.8
