Flex BMR 481 P1E+ User Manual Download | Manualshive

Page: 3 / 12

background image

Reference Board BMR 481 P1E+

287 01-ROA 170 014 Rev A 2018-10-16

3 (12)

Contents

Introduction .......................................................................................... 4

How to contact Flex ............................................................................... 4

Prerequisites .......................................................................................... 4

Reference Board ROA 170 014 ............................................................ 5

Power-up and Power-down Instructions ............................................ 7

Power-up instruction .............................................................................. 7

Power-down instruction .......................................................................... 7

Board Supplies ..................................................................................... 8

Address Resistor ................................................................................. 9

Adjustment of address resistor ............................................................... 9

Phase Active LEDs .............................................................................. 9

Test Points and Sense Locations ..................................................... 10

VIN/VOUT test points ........................................................................... 10

Sense location jumpers ........................................................................ 10

PWM test points ................................................................................... 10

Additional Output Capacitance ......................................................... 11

Current Sense termination ................................................................ 11

Electronic loads ................................................................................. 12

«
1
2
3
4
5
...
»

Summary of Contents for BMR 481 P1E+













Reviews:

No comments

Related manuals for BMR 481 P1E+

SolarCell Remote

Brand: Samsung Pages: 2

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: Mackie Pages: 4

Brand: Tamas Pages: 12

Brand: MaintTech Pages: 28

S3500 Series Uplink Module

Brand: Aruba Pages: 8

Brand: Lutron Electronics Pages: 2

Brand: Gecko Pages: 82

Brand: National Instruments Pages: 22

Brand: Swagelok Pages: 16

Brand: MERCATOR Pages: 4

Brand: W&T Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands