GE MH 18.0-EC
21
Battery state of charge
Press the button to check the state of
charge at the state of charge indicator
LEDs.
The indicator goes out after 5 seconds.
If one of the LEDs flashes, the battery must
be recharged. If none of the LEDs light up
after the button is pressed, the battery is
faulty and must be replaced.
Using a dust extraction system
CAUTION!
–
When using the wall sander, connect
a Class M dust extractor.
–
If a dust bag is used which is not autho-
rised for use with dry construction dust,
the amount of dust particles in the air
may increase at the work place.
Over a prolonged period high concentra-
tions of dust in the air may damage
the human respiratory system.
Insert the special dust bag for dry con-
struction dust into your dust extractor
according to the instructions supplied
with the dust extractor.
Connect extraction hose to the dust
extraction system. Follow the operating
instructions for the dust extraction sys-
tem! Check the attachment!
If required, use an appropriate adapter.
NOTE
If your dust extractor requires a special
connector, the clip-on connection can
be removed and a matching adapter selec-
ted from the FLEX accessories range.
Attaching and changing the sanding
tools (Figure H)
CAUTION!
Remove the battery before carrying out any
work on the power tool.
Remove worn sanding tool from
the Velcro pad.
Place the sanding sheet in the centre
of the Velcro pad and press on.
Conduct a test run to check that the san-
ding tool is clamped in the centre.
CAUTION!
Never use the Velcro pad as a sanding tool.
Never use the wall sander without the san-
ding sheet, otherwise the work surface will
be seriously damaged!
Switch on and off (Figure I-K)
Brief operation without engaged switch
rocker (Figure I)
Press and hold down the switch.
To switch off, release the switch.
Continuous operation with engaged
switch rocker (Figure I-K)
Press and hold down the switch (1.).
To lock into position, hold down the locking
button (2.) and release the switch.
To switch off, briefly press and release
the switch.
Preselecting the speed (Figure L)
To set the operating speed, move the dial
to the required value.
Gently press the switch to accelerate the
power tool up to the preselected speed.
Using bar-type handle (optional)
To stabilise the working position, it is
possible to mount a bar-type handle on the
handle tube. The mounting position can be
determined individually.
Using adapter for suction hose
(optional)
The adapter can be used for connecting
suction hoses of different dimensions.
Working with the power tool
(Figure M)
CAUTION!
Hold the electric power tool with both hands!
When working, always have one hand
on the handle – even when working with
attached extension. Keep your hands away
from the sanding head.
Otherwise, your hand could become caught,
as the sanding head swivels in different
directions.
1. Attach sanding tool.
2. Connect dust extraction system.
Summary of Contents for GE MH 18.0-EC
