LRP 1503 VRA
15
Do not work on materials which release
hazardous substances (e.g. asbestos).
Never grind or cut light metals which have
a magnesium content greater than 80 %.
Risk of fire!
Connect devices, which are used outside or
are exposed to extreme metal dusts, via an
earth leakage circuit breaker (release current
maximum 30 mA). Do not use any worn,
torn or severely clogged sanding belts.
Damaged sanding belts may rip, fly off and
cause an injury.
Before using the machine, check that the
grinding tools have been installed and
secured correctly. Switch on the machine
at no load for 30 seconds!
Interrupt the test run immediately if violent
vibrations occur or other damage is
established. Check the machine to
determine the cause.
Do not load the belt sander to such an
extent that it comes to a standstill or the
sanding belt slips.
Before putting the belt sander down, switch
it off and wait until it comes to a standstill.
Do not clamp the belt sander in a vice.
Always lay the power cord to the rear away
from the belt sander.
Clamp the workpiece if it is loose or not
positioned securely by its own weight.
Store and handle grinding tools according
to the manufacturer’s instructions.
Additional safety instructions
Use only extension cables permitted for
outdoor use.
Identify the power tool with stickers only.
Do not drill any holes into the housing.
The mains voltage and the voltage
specifications on the rating plate must
correspond.
Noise and vibration
The noise and vibration values have been
determined in accordance with EN 60745.
The A evaluated noise level of the power tool
is typically:
– Sound pressure level:
86 dB(A);
– Sound power level:
97 dB(A);
– Uncertainty:
K = 3 dB.
Total vibration value (when sanding metal
pipes):
– Emission value:
a
h
= 2.5 m/s
2
– Uncertainty:
K = 1.5 m/s
2
t^okfkd>
qÜÉ=áåÇáÅ~íÉÇ=ãÉ~ëìêÉãÉåíë=êÉÑÉê=íç=åÉï=
éçïÉê=íççäëK=a~áäó=ìëÉ=Å~ìëÉë=íÜÉ=åçáëÉ=~åÇ=
îáÄê~íáçå=î~äìÉë=íç=ÅÜ~åÖÉK
klqb
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given in
EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary
assessment of exposure. The declared vibration
emission level represents the main applications of
the tool. However if the tool is used for different
applications, with different accessories or poorly
maintained, the vibration emission may differ.
This may significantly increase the exposure level
over the total working period.
For a precise estimation of the vibration load the
times should also be considered during which the
power tool is switched off or even running, but not
actually in use. This may significantly decrease the
exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
`^rqflk>
tÉ~ê=É~ê=éêçíÉÅíáçå=~í=~=ëçìåÇ=éêÉëëìêÉ=
~ÄçîÉ=UR=Ç_E^FK
Summary of Contents for LRP 1503 VRA
Page 1: ...LRP 1503 VRA ...
Page 185: ......
Page 186: ...327 263 06 2015 Für Druckfehler keine Gewähr Technische Änderungen vorbehalten ...
