background image

Opera ng Instruc ons

 

8

 

Keep all persons away from the 

discharge opening of hoses or  tools 

or other points of compressed air 

discharge. If the machine is 

installed in an enclosed area, be 

sure to vent the relief valve   outside

 

of the structure or to an unoccupied  area.

 

11.

12. Make sure all hose connec ons are adequate- 

ly secured to prevent tools or hose ends from 

being accidentally  disconnected. 

Start-Up

 

1. This  unit  is  shipped  with  pump  break-in  oil

and should be ready to operate. Be sure  to

check for proper oil level before opera ng

the compressor. Oil should be in center of

site glass. See 

gure  8.

Use only Flexzilla Compressor Oil.

Use of any other product will 

cause product damage and void

the warranty.

2. Check for proper belt tension. There should

be 1/2 inch slack. Refer to maintenance  sec- 

on if adjustment is necessary.

Always make sure main power is 

o

 before touching belts or other 

moving parts of compressor.

 

3. Lightly push power switch to make sure sys- 

tem is  working.

4. If motor sha  is not turning counter clock- 

wise, disconnect power to terminal block

then exchange any two of the three power

leads. Re-check  rota on.

Oil level should be to 

center of red circle in 

site glass

 

Figure 9: Con nuous run feature  

 

 

Con nuous Run Feature 

(if equipped)

 

For heavy use applica ns such as sandblas ng, the 

con nuous run feature is available. This feature keeps 

main feed line open to eliminate numerous motor 

starts/stops and to help cool pump. 
To engage con nuous run feature, open ball valve 

found by following copper tubing across cylinder heads 

to tank. See 

gure   9. 

Stop con nuous run feature by closing valve so com- 

pressor will start and stop according to pressure    switch. 

Maintenance

 

Safety Steps

 

Disconnect, tag and lock out  power 

source then release all pressure  from 

the system before a emp ng to 

install, service, relocate or perform 

ANY maintenance.

 

1. Make sure repairs are done in a clean, dry, well

lit and ven lated area.

2. When cleaning, use air pressure less than  30

psi  (2.1bar). NEVER use 

ammable solvents

for cleaning purposes. Also use e

ec ve chip

guarding and personal protec ve equipment

per OSHA standard 29 CFR 1910.242  (b).

3. Relieve all internal pressure prior to   opening

any line, 

ng, hose, valve, drain plug, con- 

nec on or other component, such as 

lters and

line oilers, and before re

lling op onal air line

an -icer systems with an freeze compound.

4. Keep electrical wiring, including all terminals

and pressure connectors,  in good condi on. Re- 

place any wiring that has cracked, cut  or oth- 

erwise damaged insula on. Replace terminals

that are worn, discolored or corroded. Keep all

terminals and pressure connectors clean and

ht.

To pump

unloaders

Open ball valve

to engage

feature

Select air tools, air hoses, pipes, valves, filters 

for these items.

 

TO ACTIVATE

WARRANTY

Scan or go to 

for warranty registration

Warranty only valid by following conditions expressed in the Warranty Statement section of the Compressor Operating Manual.

Figure 8: Check proper oil level 

Summary of Contents for FI05V080Y1S












Reviews: