background image

MWI-05-001 – Rev. B 

12 

 

6.

 

Limited Warranty 

Duration of the Warranty:

 Flight Light Inc. warrants all of the goods which it has manufactured to be 

free of material defects for the following durations. 

Lamps: For a period of 90 days from the date of shipment to Buyer. Product liability is limited to lamp 
replacement and does not include incidental labor. 

FAA products: For a period of one year from the date of installation or two years from the date of 
shipment to Buyer.  

LED Light Fixtures: For a period of 2 years from the date of shipment to Buyer. Complete Systems: 
Systems including at least one Flight Light Inc. Controller and one Flight Light Inc. LED Light Fixture, for a 
period of 5 years from the date of shipment to Buyer. 

Buyer’s Remedies:

 If any such goods are found to be materially defective within the warranty period, 

Flight Light Inc. agrees to attempt to repair, and if unable to repair, to replace the defective goods 
without charge to Buyer.  

Buyer’s remedy with respect to such goods is limited to repair or replacement. For goods not 
manufactured by FLI, Buyer agrees to accept as its sole remedy the warranty, if any, offered by the 
manufacturer or manufacturers of such goods. FLI makes no warranties, express or implied, other than 
those stated in this paragraph.  

Warranty Exclusions:

 Flight Light Inc. shall not be liable under this warranty if any of the following 

conditions apply: 

 1) Unauthorized personnel attempt any repairs to Flight Light Inc. products without Flight Light   
Inc. consent.  
 2) Products are damaged by natural phenomenon, misuse, abuse, accident, alteration, or 
incorrect electrical current or voltage.  

        3) Products are improperly installed, or damaged in shipping. 

Warranty Limitations 
FLI makes no warranties, express or implied, other than those stated herein. FLI does not warranty the 

workmanship of the installer, damage caused by acts of nature, vandalism, improper installation, or 
damage caused by improper maintenance. The warranty period of LED fixtures covered under the 5-year 
system warranty is reduced to two years when fixtures are subjected to abrasive materials or chemicals. 
FLI reserves the right to either repair or replace any defective component covered under the terms of any 
of its warranties. FLI is not an engineering firm and makes no expressed or implied warranty as to the 

applicability of its products or systems in any specific situation, application or location: such decisions are 
the responsibility of the owner, design engineer and/ or others. Therefore, as to all goods sold by FLI, FLI 
hereby disclaims any implied warranty of merchantability or implied warranty of fitness for a particular 
purpose and Buyer agrees that FLI shall not be liable for any special, indirect, incidental, consequential or 
liquidated damages of any kind, whether the Buyer’s or any other claim is based upon contract, tort or 

any other legal theory. 

 

Summary of Contents for L810LED
















Reviews: