Flightcell DZM Operation Manual Download

Page: 4 / 88

| Flightcell

DZM Operating Manual | Firmware v2.00

Page 4 of 88 |

Setting automatic GPS transmission based on heading change ................................................................ 35

Heading Timer ....................................................................................................................................... 36

Setting GPS display options .................................................................................................................... 37

Using automated flight following (AFF) ........................................................................................................ 38

Registering AFF mission start and end points .......................................................................................... 38

Controlling audio settings ............................................................................................................................ 40

Accessing the Audio Menu ...................................................................................................................... 40

Setting satellite phone audio volume ....................................................................................................... 41

Setting cell modem audio volume ........................................................................................................... 41

Isolating (muting) phones....................................................................................................................... 42

Setting auxiliary device audio volume ...................................................................................................... 43

Muting auxiliary devices .......................................................................................................................... 44

Using Flightcell

DZM common setup features ............................................................................................. 45

Accessing the Setup Menu ...................................................................................................................... 45

Using Auto Power On ............................................................................................................................. 45

Setting backlight brightness .................................................................................................................... 46

Setting backlight mode ........................................................................................................................... 46

Setting LCD contrast ............................................................................................................................... 47

Identifying firmware version and serial number ....................................................................................... 48

Emergency procedures ................................................................................................................................ 49

Sending a distress signal ........................................................................................................................ 49

Flightcell

advanced setup guide ......................................................................................................... 50

Configuring your Iridium satellite phone ...................................................................................................... 51

Configuring satellite phone service center number ................................................................................... 51

Overriding satellite phone antenna lock ................................................................................................... 51

Configuring GPS tracking ............................................................................................................................. 52

Using the Installation Settings Menu to access advanced settings ................................................................. 54

Configuring Advanced Tracking Settings ...................................................................................................... 55

Enabling manual GPS tracking ................................................................................................................ 55

Using GPS antenna diagnostics ............................................................................................................... 56

Setting automatic GPS transmission based on low speed limit .................................................................. 57

Setting automatic GPS transmission for takeoff and landing based on collective switch position ................ 58

Setting automatic GPS transmission for takeoff and landing based on squat switch position ..................... 60

Configuring oil pressure switch to record aircraft operating time .............................................................. 60

Finding messaging destination addresses ................................................................................................ 62

Configuring satellite messaging destination ............................................................................................. 62

Configuring cellular messaging destination .............................................................................................. 64

Configuring position report transmission options ..................................................................................... 65

Setting preferred messaging device ........................................................................................................ 66

Enabling Iridium SBD transmission .......................................................................................................... 66

Setting satellite message size ................................................................................................................. 67

Sending GPS location upon power up ...................................................................................................... 67

Enabling and disabling automated flight following (AFF) .......................................................................... 68

Summary of Contents for DZM

























































































Search results

Summary of Contents for DZM

Reviews:

Related manuals for DZM

Brands by name

Popular brands

Flightcell DZM, Operation Manual

Search results

Summary of Contents for DZM

Reviews:

Related manuals for DZM

Brands by name

Popular brands