background image

432-0007-00-28-en-US  v100   

Integration with NMEA Devices – Application Note 

 

Overview 

This document describes how to integrate a FLIR MV-Series thermal camera with devices that use National 
Maritime Electronics Association (NMEA) communications. In particular, the camera can receive NMEA 
0183 sentences from various types of devices, including: 

 

Radar  

 

GPS 

 

Gyrocompass 

In general, there are several ways to interconnect the camera and NMEA 0183 devices

1

. This document 

describes a few typical installations and provides information specific to the following third-party (non-
FLIR) equipment: 

 

Moxa NPort Serial Ethernet Server  

 

Actisense NMEA Multiplexer 

 

ShipModul NMEA Multiplexer 

 

Antaira Power over Ethernet (PoE) switch 

 

Radar (generic NMEA 0183serial) 

 

A Windows PC (with a web browser and optionally running FLIR Sensors Manager software) 

Of course it is possible to use a wide variety of other brands of third-party devices, and the devices listed 
above are used as an example. The configurations provided in this document have been tested by FLIR 
with the MV-Series cameras. 

Scope 

This document provides a brief guide to connecting and configuring the necessary components for using 
NMEA 0183 devices with the FLIR camera. The user should have a basic understanding of the installation of 
these devices and the cables and interconnections between them. Complete details about the NMEA 
communications, configuration of cameras, IP networks and so on are generally beyond the scope of this 
document. 

FLIR Certified Maritime Integrator (FCMI) Training 

This configuration guide provides a brief description of the setup of these devices. For installers and 
integrators that are interested in a more advanced level of configuration, the FLIR Certified Maritime 
Integrator (FCMI) certification program offers hands-on training with a variety of FLIR cameras, and focuses 
on integration design and installation with other third-party devices and equipment. For more information, 
contact your local FLIR representative or visit one of the following web sites: 

http://www.flir.com/training 

                                                 

1

 At this time, other maritime communication protocols such as NMEA 0183-HS and NMEA 2000 are not supported. 

Summary of Contents for MV series























Reviews: