background image

-

1

-

FLOMEC

®

 QS200

INSTALLATION GUIDE

The FLOMEC QS200 provides a robust ultrasonic 

flowmeter for irrigation applications. The QS200 uses 

Percentage of Reading (RD)

 Accuracy which is superior to 

an impeller flow sensor/flowmeter that uses 

Percentage 

of Full Scale (FS) Accuracy

 (

download the FLOWMETER 

ACCURACY WHITE PAPER for more information on RD and 

FS information @ http://bit.ly/flomec-accuracy-wp

). Also, 

the QS200 does not have any moving wetted parts, so 

there is no need to replace damaged parts.

This meter uses a two-wire system that is connected to an 

irrigation controller’s flow sensor input (or decoder’s flow 

sensor port) and meets the cable distance recommended 

by Irrigation controller/decoder manufacturers. The 

two-wire system communicates via a square wave pulse 

that is converted to flow rate at the controller (identical 

to an impeller flow sensor communicating to irrigation 

controller/decoder). The QS200’s power is supplied 

through these same two wires by the controller’s/

decoder’s flow sensor input/port 

 

(voltage range of 7.5 V

DC

 to 36 V

DC

).

The following lengths of straight pipe should be connected to the QS200 FLOMEC Tee (or NON-FLOMEC Tee):

 

-

10 times the pipe’s inner diameter upstream of the meter

 

-

5 times the pipe’s inner diameter downstream of the meter

The pipe needs to be full of irrigation water with no air inside. Built-up sediment on the QS200’s transducers or large 

debris can greatly hinder the meter’s performance. Keep the following in mind when installing:

 

-

Install QS200 at an angle as shown in Figure 1a.

 

-

1 inch pipe installations will need a larger angle 

of 45 degrees.

 

-

Flow direction arrows on the QS200 insert must 

match flow direction of water through the pipe 

(see Figure 1a).

 

-

FLOMEC Tee is bidirectional for flow (the QS200 

insert 

IS NOT

 bidirectional - the flow direction 

matters).  

 

-

Flow direction of the QS200 should be horizontal 

or upward. 

DO NOT

 install flowmeter in a 

downward flow direction, to avoid partially filled 

pipes (see Figure 1b).

 

-

When installing below ground, install meter in a 

valve box with a thick layer of gravel below the 

meter.

 

-

DO NOT

 direct bury QS200 flowmeter.

 

-

If using a Non-FLOMEC Tee, verify the QS200 

insert physically fits into the Non-FLOMEC Tee.

 

-

DO NOT

 pull on the QS200 wires under any 

circumstances.

 

-

Confirm that the Controller/Decoder flow sensor 

input (or port) will supply the QS200 two-wire 

meter with the appropriate power 

 

(7.5 V

DC

 to 36 V

DC

).

08/20  IND-1126 Rev A QS200 Installation Guide

GENERAL INSTALLATION PROCEDURE

IMPORTANT: 

Read the General Safety Instructions for this flowmeter (see last page) before beginning any installation procedures.

Summary of Contents for QS200









Reviews: