background image

Meteor 250 MkII 

1800 356 673 

13.

  

1800 - FLOOREX

 

 

Electrical safety 

 

1.

 

All electrical maintenance and repairs to be carried out by qualified 

persons only. 

2.

 

CAUTION

 - Line terminals may be alive when main switch is in the off 

position. Disconnect all power at source before performing any 

maintenance or repairs

.

 

3.

 

WARNING - DO NOT

 operate the machine with any electrical panels open. 

4.

 

WARNING 

- The METEOR 250 MKII has an overload switch and will trip 

when under excessive load and will not allow the machine to be switched 

on if it is overloaded. (Overload will need to be reset when safe to do so).

 

Continuing to use the METEOR 250 MKII when constant tripping occurs, 
VOIDS THE WARRANTY!

 

5.

 

Never operate machine in the rain or if heavy moisture is present. 

6.

 

The overcurrent device is there to protect you and the machine from 
harm. 

DO NOT

 alter or adjust the over load in any way. If it is faulty, only 

replace with original part that is identical to the faulty one. 

7.

 

Never bypass over-current devices in this machine. 

8.

 

Never connect or disconnect power cables with voltage present or while 
under load. 

9.

 

Disconnect all power connections and observe lock out / tag out 
procedures before attempting to carry out any maintenance or repair on 
any equipment. 

10.

 

Avoid any contact with any rotating parts or driven parts. 

11.

 

Never use equipment that has not been tested and tagged (including 
cords). 

12.

 

Do not operate METEOR 250 with any covers or doors removed or open. 

13.

 

Before connecting the machine to power, check the condition of all power 
leads and cables on, or used in conjunction with the machine. DO NOT 
USE it if any fault(s) cuts; wear marks, Bare wires out of plugs or sockets, 

etc…  
Get qualified persons to repair and re-tag it as required by regulations in 
your country. 

 

 

Summary of Contents for Meteor 250 MkII





























Reviews: