background image

  

 

**The 

TrimLine

 can be set up by one person, made easier with our optional

 

EasyRiser Kit

.   As with 

any

 canopy though, set up is easiest with help!

Before beginning assembly of your TrimLine, review the enclosed Parts List to familiarize yourself with 
the TrimLine, and to confirm that all parts are present.  

Also, review these instructions and the instructions for any accessories you have purchased, such as 
Awnings, StaBar kit, or Rear Door assemblies.  Parts for TrimLine accessories are often installed as the 
TrimLine is being set up.  Reviewing all instructions before beginning set up will help you get the 
necessary accessory parts in place as you set up your TrimLine.

TRIMLINE CANOPY 10’ x 10’ 

Instructions for Assembly

Please, assemble the TrimLine at home the first time, not at a show.

Visit our website to see all options available for the TrimLine: 

flourishdisplays.com

Video instructions are available on our website!

Go to: 

flourishdisplays.com/instructions 

or scan this code with your QR Code 

Reader App for a direct link to our instructions and videos.

Summary of Contents for TRIMLINE CANOPY 10' x 10'











Reviews: