22
9. Remove th
retaining s
10. Disconnec
the driver
11. Use the ¼
from the d
12. Unplug the
module as
13. Feed the t
driver mod
driver mod
the driver
cutting the
14. Grasp the
clockwise
retract the
15. Remove th
driver mod
16. Verify that
driver mod
driver mod
in position
17. Gently inse
compartme
clockwise
rotating the
18. Once the d
threads ar
counter clo
the flat on
screw hole
19. Verify that
driver mod
20. Insert a dr
through th
housing. T
21. Reach thro
module co
barbed fitt
¼ in. nutdr
NOTE:
Do
older Logix
that will no
Orifices ar
colored.
22. Reconnec
the barbed
he plastic board
screws. (See fi
ct the flexible tu
module assem
¼ in. nut driver t
river module a
e two wiring co
ssembly to the
wo wires on th
dule compartme
dule opening. (
module to thre
e wires.
base of the dri
to remove. Aft
driver module
he barbed fittin
dule using the ¼
the O-ring is in
dule. Lay the w
dule as shown
by hand.
ert the driver m
ent in the hous
to thread it into
e driver module
driver module h
e fully engaged
ockwise until th
the housing ar
e for the next st
the nylon gaske
ule retaining sc
river-to-housing
e counter-bore
Tighten with a
ough the main
ompartment of t
ing on the side
river.
o not mix the ba
x positioners.
ot work in the L
re brass-colore
t the flexible tu
d fitting.
d cover by rem
igure 14.)
ubing from the
mbly. (See figur
to remove the b
ssembly.
nnections that
main PCB asse
e driver modul
ent so that they
(See figure 11.
ad out without
iver module an
ter it is threade
from the hous
g from the side
¼ in. nut driver
n place on the
wires back alon
in figure 11 and
module into the
sing. Turn the d
o the housing.
e until it bottom
has bottomed o
d, rotate the dr
he flat on the d
re aligned. Thi
tep.
et is in the coun
crew hole as sho
g screw into the
ed hole in posit
Phillips screwd
compartment i
the positioner a
e of the driver m
arbed fitting wit
Older models c
Logix 320000M
d, barbed fittin
ube coming from
Use
moving the three
barbed fitting a
re 14.)
barbed fitting
link the driver
embly.
e back into the
y stick out the
) This will allow
tangling or
nd turn it counte
ed out, carefully
ing.
e of the new
r.
top of the new
ng the side of th
d hold the wire
driver module
driver module
Continue
ms out.
out so that the
river module
river module an
s will align the
nter bore in the
own in figure 13
e driver housin
ioner main
driver.
nto the driver
and install the
module using th
th those from
contain orifices
D model.
gs are silver-
m the regulator
er instructions –
e
at
e
w
er-
y
he
es
nd
3.
g
he
s
r to
23. Fee
the
Ass
24. Ver
the
be p
25. Car
top
26. Car
mac
(Fig
unti
hole
27. Inst
a Ph
28. Slid
valv
Inst
(See
29. Inst
scre
and
ove
30. Rec
perf
31. Rei
Figure
– Digital Positio
ed the driver m
housing, and c
sembly.
rify that the thre
machined platf
placed. (Figure
refully slide the
of the driver m
refully slide the
chined surface
gure 13.) Slide
l the two retain
es in the base.
tall two spool-v
hillips screwdri
de the spool va
ve until the tang
tall spool valve
e figure 12).
tall the plastic b
ews through th
d tighten evenly
r tighten. (See
connect power
form a stroke c
nstall all cover
15: Main PCB
oner 3200MD
odule wires int
connect them t
ee O-rings are
form where the
e 24.)
e spool into the
module assemb
e block over the
of the housing
e the block towa
ning holes line
valve screws an
iver. (See figu
alve cover asse
g engages into
cover screw a
board cover. In
e plastic cover
y, using a Philli
e Figure 15.)
and air supply
calibration.
rs.
Assembly
LGENIM0059-
flowse
to the main cha
o the main PC
in the counterb
e spool valve b
connecting cli
ly.
e spool, using t
g base as a reg
ard the driver m
up with the thre
nd tighten secu
re 13.)
embly over the
o the housing s
and tighten sec
nsert the three
r into the thread
ps screwdriver
y to the position
-04 09/11
erve.com
amber of
B
bores on
block is to
p on the
the
gister.
module
eaded
urely with
spool
lot.
urely.
retaining
ded boss
r. Do not
ner and
