background image

Inst464 

 Viron e-Quilibirum Series Chlorinator Instructions V07-20 

24 

 
 
At most, CyA should be managed and kept within a range of 10 to 20 ppm when used in conjunction with the e-Q 
chlorinator installed with the Chlorine Sensor. Ongoing use of Trichlor or Dichlor will continue to raise the level of 
CyA causing a reduction in the activity of the chlorine and may cause your e-Q Chlorinator to continue to raise the 
chlorine levels to excessive levels in order to reach the chlorine set point (ORP). 
 
If CyA is present in the pool water or Trichlor or Dichlor is used to supplement the Chlorinator’s chlorine production 
then the ORP set point should be adjusted downwards until a chlorine level of between 2 and 5 ppm is achieved 
and maintained. Consult your pool professional or certified Viron Installer to adjust your Chlorine (ORP) set point. 
 
As a guide, the following set point ORP levels can be used as a starting point to achieve a consistent and 
reasonable chlorine level. 
 
 
 

Guide to adjusting the Chlorine (ORP) set point 

Constants:  pH at 7.6, TA at 180 ppm 

 

  

Chlorine Level 

Cyanuric Acid 
Level 

2 ppm 

3 ppm 

4 ppm 

700 mv 

725 mv 

750 mv 

10 

550 mv 

600 mv 

625 mv 

20 

500 mv 

525 mv 

550 mv 

>50 

350 mv 

400 mv 

450 mv 

 
Check your chlorine after 48 hours and adjust the chlorine (ORP) set point up or down as necessary.

  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for AstralPool Viron EQ





























Reviews: