268XA
Service Manual
4-12
Analog Channel Integrity Test
The following procedure tests the integrity of each analog channel (2 to 20) to verify each
analog channel is capable of making measurements.
1.
Configure Channel for Ohms Using the Fluke DAQ software, configure channels
2 (then 3, then 4, etc. as this step is repeated) to 20 for Ohms 2W, 300 range [PAI] or
30 k range [FAI].
2.
Connect Test Leads Remove the Universal Input module from the device,
disconnect the test leads and connect them to the channel under test (starting with
channel 2). Reinstall the Universal Input module in the device.
3.
Open Spy Open the Spy window under the Configuration dialog.
4.
Verify Reading Alternately open and short the test leads observing the measurement
for the analog channel under test in the Spy window shows Overload for opened
leads and very low resistance for shorted leads (less than 10
Ω
for the PAI, or less
than 1 k
Ω
for the FAI).
5.
Repeat Test for each Channel Repeat steps 2 to 4 for each channel (3, 4, 5, and so
forth to channel 20).
Open Thermocouple Response Test
This test checks the Open Thermocouple response.
1.
Connect an 820 Ohm Test Resistor Remove the Universal Input module from the
device and connect an 820
Ω
resistor to the channel 1 terminals. Reinstall the
Universal Input module.
2.
Configure Channel 1 for Thermocouples In Fluke DAQ, configure channel 1 for
Thermocouples with Range (thermocouple type) K.
3.
Open Spy Open the Spy window under the Configuration dialog.
4.
Connect a 10 k Ohm Test Resistor Remove the Universal Input module from the
device and connect a 10 k
Ω
resistor to the channel 1 terminals to simulate an open
thermocouple condition. Reinstall the Universal Input module.
5.
Verify Open Thermocouple The Spy window indicates an open thermocouple
detect condition by displaying Open TC in place of a temperature reading.
Summary of Contents for 2680A
