background image

Lifetime Limited Warranty 

Each Fluke 20, 70, 80, 170 and 180 Series DMM will be free from defects in material and workmanship for its lifetime. As used herein, “life-
time” is defined as seven years after Fluke discontinues manufacturing the product, but the warranty period shall be at least ten years from 
the date of purchase. This warranty does not cover fuses, disposable batteries, damage from neglect, misuse, contamination, alteration, 
accident or abnormal conditions of operation or handling, including failures caused by use outside of the product’s specifications, or normal 
wear and tear of mechanical components. This warranty covers the original purchaser only and is not transferable. 

For ten years from the date of purchase, this warranty also covers the LCD. Thereafter, for the lifetime of the DMM, Fluke will replace the 
LCD for a fee based on then current component acquisition costs.  

To establish original ownership and prove date of purchase, please complete and return the registration card accompanying the product, or 
register your product

.

 Fluke will, at its option, repair at no charge, replace or refund the purchase price of a defective product purchased 

through a Fluke authorized sales outlet and at the applicable international price. Fluke reserves the right to charge for importation costs of 
repair/replacement parts if the product purchased in one country is sent for repair elsewhere.  

If the product is defective, contact your nearest Fluke authorized service center to obtain return authorization information, then send the 
product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk 
for damage in transit. Fluke will pay return transportation for product repaired or replaced in-warranty. Before making any non-warranty re-
pair, Fluke will estimate cost and obtain authorization, then invoice you for repair and return transportation.  

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE 
EXPRESSED OR IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM-
AGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT 
AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON FLUKE’S BEHALF. Since some states do not allow the exclusion or limita-
tion of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you. If any provision of this 
warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity 
or enforceability of any other provision.  

2/02 

Summary of Contents for 77 Series IV























Reviews: