background image

Y

X

Maintenance

W

V

WARNING
Cutting head continues to rotate after the
trimmer has been switched off.  Keep fingers
and hands clear of the line cutter on leading
edge of guard.

Caring

After you have finished using your product follow the
procedure below:

AVOID ACCIDENTAL STARTING.  KEEP FEET
AWAY FROM THE SWITCH LEVER WHEN:
CLEANING AROUND THE INSIDE OF THE SAFE-
TY GUARD, REMOVING OR REFITTING SPOOL
CAP, MANUALLY FEEDING OR REPLACING
NYLON LINE.

1. Disconnect from the mains electricity supply.
2. Never clean your trimmer with water, cleaning flu-

ids, or solvents, just remove debris with a suitable
tool, a soft brush or dry cloth.

3. Using a soft brush, clean around the inside of the

safety guard, the cutting head 

(Fig V)

and the

motor housing air vents. 

(Fig W)

4. Remove the wheel by pressing one of the but-

tons.  Clean the wheel and groove on trimmer
head with a soft brush 

(X & Y)

.

5. Attach wheel as described in 

Wheel Assembly

.

6. Inspect the trimmer carefully, especially the parts

of the cutting head.

7. If your trimmer is damaged in any way contact

your local approved service centre.

Never use a damaged trimmer.

8. Store in a cool, dry place and out of reach of chil-

dren.

Fault Finding Chart

FAULT

CHECK

ACTION

Is the automatic line feed work-
ing?

Manually feed out line.

SEE “MANUAL LINE FEED”

Is the line fed out and visible?
Has line been removed from
cleat?

Remove cap and spool, free line
and re-fit spool and cap.  

SEE

“CUTTING HEAD”

The line may be jammed on the
spool.  Rewind line to remove
crossed loops. Check that line is
in correct section of spool.

Is the manual line feed working?

Has too much line been fed out?

SEE “MANUAL LINE FEED”

Contact your local approved Service
Centre or Husqvarna Outdoor
Products Customer Service.

Is the line cutter missing from
the safety guard?

Contact Husqvarna Outdoor Products Customer Service 
Telephone : 0870 609 1901

No

No

No

Yes

Yes

LINE NOT FEEDING

OR

LINE TOO SHORT

OR

TRIMMER VIBRATES

CONTINUOUS CLATTER-

ING NOISE 

LINE SNAPS CONTINU-

OUSLY

IF NONE OF THE ABOVE 

OR IF FAULT PERSISTS 

Has the motor reached full
speed before use?

No

Allow the motor to reach full speed
before use.

Are you using the trimmer cor-
rectly?

?

Only use tip of nylon line to trim.

SEE “How to trim and edge”

Is the line jamming on the
spool?

Yes

Rewind the line on the spool, if
symptoms still persist, change
spool and line.

Clean wheel and groove on trimmer head.  

SEE “MAINTENANCE”

WHEEL STOPS TURNING

Summary of Contents for CCT25









Reviews: