a risk that the polybag can suffocate toddlers.
Warning! When wearing hearing protection, and due to
the noise produced by the unit, the operator may not
notice persons approaching.
If the unit starts unintentionally when the mains plug is
connected, disconnect the mains at once.
Contact FLYMO Service to check the unit.
Warning! This unit makes an electromagnetic field while
it operates. This field may under some con ditions interfere
with active or passive medical implants. To decrease
the risk of conditions that can possibly injure or kill, we
recommend persons with medical implants to speak with
their physician and the medical implant manufacturer
before operating.
If your trimmer is damaged in any way contact your local
approved service centre.
v
Never use a damaged trimmer.
Inspect the area to be cut before each use. Remove all
objects such as stones, broken glass, nails, wire, string
etc, which can be thrown or become entangled in the
trimmer head.
Warning: The cutting line continues to rotate after
the machine has been switched off.
Warning: Beware of finger entrapment while
putting the upper and the lower shaft together
[Fig. A1].
Unplug the device immediately in case it doesn’t stop
anymore.
Do not lean over the trimmer guard – objects may be
thrown by the cutting line.
Don’t use the trimmer for pond, river, stream, or creek
care. Water in the product could cause a malfunction, or
an electrical shock.
Do not operate the trimmer in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Trimmers create sparks which may ignite the dust
or fumes.
If the unit starts unintentionally when the mains plug
is connected, disconnect the mains at once.
Contact FLYMO to check the unit.
2. ASSEMBLY
CAUTION!
The trimmer may only be operated provided
that the protective cover
0
is assembled.
To assemble the trimmer:
1. Insert the tube into the switch handle [Fig. A1].
Make sure that the internal cable is not twisted.
2. Push until it clicks into position.
Make sure that the tube is fully located by attempting to
remove it.
3. Insert the tube into the trimmer head [Fig. A2].
Make sure that the internal cable is not twisted.
4. Push until it clicks into position.
Make sure that the tube is fully located by attempting
to remove it.
5. Pull the lock
1
belonging to the additional handle
2
,
push in both of the snap-fits
3
belonging to the
additional handle
2
and, with the grooves
ß
R
pointing
forwards, snap them into the holder
4
[Fig. A3].
6. Place both halves of the impeller
5
around the lower
groove
6
of the trimmer head
7
and close until they
audibly engage [Fig. A4].
7. From the front, push the plant guard
8
into the upper
groove
9
of the trimmer head
7
. In doing so, ensure
that the installed bow can rotate freely (i. e. insert the
bow with the kink pointing upwards) [Fig. A5].
8. Place the protective cover
0
on top of the trimmer
head
7
[Fig. A6].
9. Turn the protective cover
0
until it can be pushed over
the trimmer head entirely.
10. Rotate the protective cover
0
anti-clockwise until it
audibly engages [Fig. A7].
3. OPERATION
DANGER! Risk of physical injury!
Cut injury when the product starts
accidentally.
v
Before you connect, adjust or transport the
product, disconnect the mains cable and trans-
port the product by the bottom handle.
To connect the trimmer [ Fig. O1 ]:
DANGER! Risk of electric shock!
To avoid damage to the mains cable
8
it
must be inserted into the cable lock
w
.
v
Before you operate the product insert the mains
cable
q
into the cable lock
w
.
1. Loop the mains cable
q
, insert the loop into the cable
lock
w
and pull tight.
2. Connect the mains cable
q
into a 230 V mains socket.
To set the work positions:
CAUTION! Avoid contact between the ground and
the trimmer head in working position 1 + 2.
Work position 1 [Fig. O2]:
For standard trimming.
Work position 2 [Fig. O3/O4]:
Trimming beneath obstacles.
1. Push the foot pedal
e
and lower the shaft downwards
into the desired working position.
2. Release the foot pedal
e
and allow the shaft to engage.
5
GB
