background image

3

Warning for AC-3S10 balance changer:

1. AC-3S10 is for charging the lion battery or the Lipo battery.It only support the charging of only one pack which is

consisted of 2 or 3 cells. It cannot charge two or more lipo battery packs, otherwise the battery and the charger will be damaged.

2. While charging, the balance charger should be out at dry and ventilated place. And it should be (kept) away from heat

source & inflammable & explosive materials.

3.

While charging, balance charger should be out of aircraft. In order to avoid accident, you should be kept an eyes on it

during charging.

4.

Please don’t charge it immediately after the battery is used or when the surface temperature does not cool down. Otherwise

battery tends to get inflated easily or even leads to fire.

5. Please check if the positive pole and negative pole are connected correctly before you connect the battery and balance

charger.

6.

When the battery is charged, please avoid any fall or external force. Otherwise it may cause the short circuit for the

positive pole and negative poles of the battery.

7.

In order to make sure the safety in use, please use the original charger and battery on request. Please remember to change the

battery when it gets aging and bouffant after using for a long time.

8.

After fully charged, the battery will discharge automatically if it is not removed from balance charger for a long time, and it

may cause power consumption. When the charging voltage is lower than nominal voltage, balance charger will recharge the
battery until it is fully charged. The battery lifetime will be shortened if it is repeatedly charged and discharged.

Flight instruction

1. Power on the

radio

1

Open the battery hatch cover of radio.

2

Install

4pcs AA batteries into the radio

3

Close the battery hatch cover of radio.

Please use correct type of battery in the flight. In order to avoid reducing the life of battery, please don’t mix up the

new battery and old battery.

Please take off the battery from the radio if you don’t use it for a long time.
Please pay attention to the electric quantity in your flight. Please change the battery in time to avoid

malfunction

caused by low voltage

during flight.

7.4V battery charge interface

11.1V battery charge interface

Status indicator

Summary of Contents for Meteor 280










































Reviews: