background image

FLYWOO Firefly 1S Nano Baby ANALOG V1.0

1/ drone introduction

Firefly 1S Nano Baby Quad is an 20g ultralight 1S Quad for freestyle and crusing. Pilots
can enjoy up to 8 minutes and 45 seconds flight time with Flywoo's latest 1S 450mah !
Through a lot of tests, we found the best configuration for Firefly 1S nano baby quad! It
is not only suitable for cruising super long flight time, but also perfect for freestyle like a
ripper.Last but not least, it is very quiet, like a mosquito, suitable for both indoors and
outdoors.

Features

1/ Equipped with GOKU Versatile F4 5-IN-1 1S AIO W/250mw VTX AIO Flight controller,
which is specially designed for 1S Nano Drone . reliable and stable
2/ No Propellers in view, NO Jello flight Footage, stable flight picture
3/ Ultralight 20g, Pilots can enjoy up to 8 minutes and 45 seconds flight time with
Flywoo's latest 1S 450mah
4/ Perfect for freestyle and crusiong
5/ it is very quiet, like a mosquito, suitable for both indoors and outdoors

Specification

Item: Firefly 1S Nano Baby Quad 40mm
Weight:20.4g
Flight Controller: GOKU Versatile F4 5-IN-1 1S AIO W/250mw VTX
Motor: ROBO 0802.4 16500KV
Compatible Propellers: Gemfan 40mm
Camera : 1.2g Flywoo 1S Nano Camera
Battery: Explorer 450mAh 1S 80C Lipo Battery for tiny quad -PH 2.0
Receiver: PNP \ SPI Frsky \ Elrs 2.4G \ TBS CRSF
Flight time:8mins with Explorer 450mAh 1S 80C Lipo Battery for tiny quad -PH 2.0

Includes

1 x Firefly 1S Nano Baby Quad 40mm Drone
2 x set of Gemfan 40MM 1610-2

Summary of Contents for Firefly 1S Nano BabyQuad










Reviews: