FMS 1:24 FCX24 MAX SMASHER Instruction Manual Download

Page: 10 / 28

This function is used to protect the safety of the model and the operator when the receiver cannot normally receive

the signal from the transmitter and is out of control. The receiver defaults that the throttle channel is fixed to be out

of control and enters the brake state. After other channels are out of control, the receiver has no signal output. If you

set it on the transmitter, it will output according to the set value.

Attention:

• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.

• Please carefully check each power device and car frame instructions to ensure the power matching is reasonable

before use. Avoid damaging power system due to incorrect matching.

• Do not let the external temperature of the system exceed 90°C /194°F , because high temperature will damage the

power system.

• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to

unintended operation or loss of control.

• After use, remember to disconnect the battery and the ESC. If the battery isn't disconnected, the ESC will consume

electric energy all the time even if it is off. It will discharge completely if connect the battery for a long time, thus

resulting in the failure of the battery or the ESC. We are not responsible for any damage caused by this!

• Make sure the receiver is mounted away from motors or any device that emits excessive electrical noise.

• Keep the antenna of the receiver at least 1cm away from conductive materials such as carbon or metal.

• Do not power on the receiver during the setup process to prevent loss of control.

Dial Switch sign

1.连接相关设备：
连接前请确认电调开关处于关闭（OFF）状态，将电机与电调的M+/M-相连接，舵机接到电调3Pin 排针接口上(“-”“+”"S”相对
应），电池与电调输入正负极对应相接。
2.正常开机，识别油门中点：
上面第一步相关设备连接好后，先打开遥控器，并将遥控器油门扳机置于中点位置（自然状态）。最后一步打开电调开关，接收机重
新上电自动识别电池类型后方可运行。注意：a.电调开机后必须等到自检完成后方可运行（大约3秒），否则可能无法正常动作；b.若
开机后无动力输出，请查看遥控器油门微调是否置于“0”位置，接收机重启可自动识别微调油门中点；c.若运行时发现电机方向不对,
将电调接电机的两根线互换位置即可；d.为了一切正常，请养成先打开遥控器最后打开电调开关以及先关闭电调开关最后关闭遥控器
的习惯。
注：关于电池类型、拖刹力度和运行模式的设置详见配套遥控器说明书相关章节。

Failsafe

失控保护

此功能用于当接收机无法正常收到遥控器的信号，不受控制时，保护模型和操作人员的安全。接收机默认为油门通道固定为失控进入
刹车状态，其他通道失控后接收机无信号输出，如若在遥控器上进行设置，则按照设置值输出。
注意事项：
•使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
•请查看各动力设备以及车架说明书，确保动力搭配合理，避免因错误的搭配导致动力系统损坏。
•勿使系统的外部温度超过90°C /194 °F,高温将会毁坏动力系统。
•关闭时，请务必先关闭接收机电源，然后关闭遥控器。如果关闭遥控器电源时接收机仍然在工作，将有可能导致遥控设备失控而引发
事故。
•使用完毕后，若长时间不玩车，切记断开电池与电调的连接。如电池未断开，即使电调开关处于关闭状态，电调也会一直消耗电能
（只是非常小），长时间连接电池最终会被过放，进而导致电池或电调出现故障。我们不对因此而造成的任何损害负责！
•确保接收机安装在远离电机或电噪声过多的区域。
•接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有1厘米以上的
距离。
•准备过程中，请勿连接接收机电源，避免造成不必要的损失。

ESC Parameter Setting

电调设置

Running Mode

FWD/REV/BRK

FWD/REV

Lipo

NiMH

50%

75%

100%

Battery Type Drag Brake

拨码开关标识