FMS J-3 V3 Instruction Manual Download

Page: 13 / 13

Trouble shooting

Problem

Possible Cause

Solution

Aircraft will not respond to

the throttlebut responds to

other controls.

-ESC is not armed.

-Throttle channel is reversed.

-Lower throttle stick and throttle trim to lowest settings.

-Reverse throttle channel on transmitter.

Extra propeller noise or

extra vibration.

-Damaged spinner, propeller,

motor or motor mount.

-Loose propeller and spinner parts.

-Propellor installed backwards.

-Replace damaged parts.

-Tighten parts for propeller adapter, propeller and spinner.

-Remove and install propeller correctly.

Reduced flight time or

aircraft underpowered.

-Flight battery charge is low.

-propeller installed backward.

-Flight battery damaged.

-Completely recharge flight battery.

-Replace flight battery and follow flight battery

instructions.

Control surface does not

move, or is slow to respond

to control inputs.

-Control surface, control horn,

linkage or servo damage.

-Wire damaged or connections

loose.

-Replace or repair damaged parts and adjust controls.

-Do a check of connections for loose wiring.

Controls reversed.

Channels are reversed in the

transmitter.

Do the control direction test and adjust controls for

aircraft and transmitter.

-Motor loses power

-Motor power pulses then

motor loses power.

-Damage to motor, or battery.

-Loss of power to aircraft.

-ESC uses default soft Low Voltage

Cutoff(LVC).

-Do a check of batteries, transmitter, receiver, ESC, motor

and wiring for damage(replace as needed).

-Land aircraft immediately and recharge flight battery.

LED on receiver flashes

slowly.

Power loss to receiver.

-Check connection from ESC to receiver.

-Check servos for damage.

-Check linkages for binding.

Spare parts list content

FMSRK101

FMSRK102

FMSRK103

FMSRK104

FMSRK105

FMSRK106

FMSRK107

FMSRK108

FMSRK109

FMSRK110

FMSRK111

FMSRK112

FMSPROP021

FMSDZ007

FMSDJ007

Fuselage

Main wing set

Horizontal stabilizer

Vertical stabilizer

Cowl

Linkage rod

Supporting bar set

Front landing gear set

Sticker

Propeller plate

Pipe

Screw set

Propeller

Motor shaft

Motor mount

FMSBM009

PRKV850

PRESC001

FMSSER9GPW

FMSCHR01

FMSFLT004

Motor board

Brushless motor

40A ESC

9g Servo

（

with waterproof function)

Charger

Float Set

Visit our website: www.fmsmodel.com to see photo of this product. Enter the key word "ESC" in the search bar for the

stock ESC instruction manual.

Summary of Contents for J-3 V3














Search results

Summary of Contents for J-3 V3

Reviews:

Related manuals for J-3 V3

Brands by name

Popular brands

FMS J-3 V3, Instruction Manual

Search results

Summary of Contents for J-3 V3

Reviews:

Related manuals for J-3 V3

Brands by name

Popular brands