background image

ENGLISH

5

Safety PrecautionS

Do not inhale fog output. Highly atomized liquid droplets can 

float in the air a long time and are quickly absorbed by the 

lungs. Depending on the material being fogged, this could result 

in serious injury or death.

Do not use to apply any liquid that is hazardous to people, 

animals or property when atomized into small droplets. The 

large surface area of small droplets increases their reactivity and 

potential to form an explosive mixture. Be aware of potentially 

dangerous interactions between liquid fog droplets and other 

aspects of the treatment area.

Read the label of the chemical you plan to use, and follow the 

instructions in its “Precautions” and “Directions for Use” 

sections. If the label lacks this information, obtain directions for 

use and safety precautions including personal protective 

equipment (respirator, face mask, special clothing) from the 

chemical manufacturer or distributor.

Keep an intake air filter in place during use. This will help 

prevent dust and fog droplets from entering the unit.

Do not atomize a flammable liquid. Electric arcs produced 

inside the motor during normal use could ignite it. 

Do not fog near an open flame.

Risk of Electric Shock – Do not expose to rain. Store indoors. 

Use only a properly grounded (earthed) three pin electric 

outlet. The ground wire is an essential safety feature of this 

product. Do not remove the grounding lug on the power cord. 

Do not use an ungrounded (“3-to-2”) plug adapter. 

An extension cord, if used, must have a continuous ground 

wire leading to earth and an amperage rating greater than the 

rated current on the fogger nameplate label. Do not chain two 

extension cords together. 

Summary of Contents for VECTRA-JET 750510CE

















Reviews: