Folding Guard Qwik-Fence, Installation Instructions Manual

FGI-011_Rev.D  08/10/2015                                                                                                          Qwik-Fence Installation Instructions                                                                                                                                        

5858 W. 73

RD

 ST 

BEDFORD PARK, IL.  60638 

Qwik-Fence

®

15 

Slide Door Assembly  

Toll Free: (800) 622-2214 
Phone: (708) 325-0400 
Fax: (708) 325-0450 

Step 9B:  Slide Door Pre-Assembly. 



Attach the Guide (B8) to the bottom back end of the door with provided Carriage Bolt (F2)  

       and Nut (F3), as shown in Figure (9B-1). 



Attach the Trolley assembly (B9) to the top of the door by inserting it into the existing holes  

       at the top of the door.  For reference use Figure (9B-2).  

Fig.

9B

‐

2

Fig.

9B

‐

1

Step

9C:

Slide

Channel

Assembly

&

A achment.



Take

the

slide

door

bracket

assembly

(

Step

9A

)

and

a ach

it

through

the

bo om

two

holes

via

a

TEK

Screw

(F1)

and

a

Washer

(F4).

Refer

to

Figure

(9C

‐

1)

for

visual

instruc ons.



Insert

the

Slide

Door

Track

inside

the

Slide

Door

Bracket

Assembly

as

shown

in

Figure

9D

‐

2.



Tighten

the

bolts

on

top

of

the

Slide

Door

Bracket

(B4)

through

the

holes

in

the

Slide

Door



Track

(D6).

Refer

to

Figure

(9C

‐

2)

for

Visual

Instruc ons.

(NOTE:

The

holes

DO

NOT

have

to

be

aligned,

however

make

sure

the

gap

between

channels

is

minimal)



If

your

Ver cal

Post

height

is

taller

then

96”

DO

NOT

a ach

the

Slide

Door

Bracket

(B4)

to

the

Slide

Door

Moun ng

Strip

(B5).

Instead

Measure

96”

from

the

ground

to

the

bo om

of

the

Slide

Door

Bracket

(B4)

and

using

a

TEK

screw

(F1)

and

(F4)

washer

a ach

directly

to

post.

Fig.

9C

‐

2

Fig.

9C

‐

1

Fig.

9D

‐

1

Step

9D:

Slide

Door

Assembly.



Take

the

Assembled

door

(

Step

9C

)

and

insert

the

trolleys

into

the

Slide

Door

Track

(D6).

See

Figure

9D

‐

1

for

reference.

Slide

the

door

all

the

way

through.

Make

sure

that

that

door

moves

freely

with

in

the

Slide

Door

Track

(D6).

Make

sure

there

is

a

2”

clearance

between

the

bo om

of

the

door

and

the

fl

oor.

If

there

is

not

adjust

the

trolleys

un l

there

is.

Please

note

that

when

inser ng

the

door

assembly

the

front

of

the

door

should

go

in

fi

rst

and

that

the

lock

should

be

facing

towards

the

direc ons

that

is

speci

fi

ed

in

the

Plan

Drawings

either

provided

by

Folding

Guard®

or

Your

Company’s

Representa ve.

A er

Inser ng

the

Door,

please

insert

the

Stop

Bolt

(F12)

into

the

free

hole

in

the

Slide

Door

Track

Assembly

on

the

back

end

of

the

door,

and

Tighten

with

Nut

(F3).

This

will

prevent

the

door

from

sliding

out

of

the

Slide

Door

Track

(D6).

CAUTION:

Door

Stop

Bolt

must

be

installed

in

order

to

prevent

the

door

from

exi ng

the

track.