background image

 

FGI-011_Rev.D  08/10/2015                                                                                                          Qwik-Fence Installation Instructions                                                                                                                                        

5858 W. 73

RD

 ST 

BEDFORD PARK, IL.  60638 

Qwik-Fence

®

 

17 

Ceiling Kit Assembly  

Toll Free: (800) 622-2214 
Phone: (708) 325-0400 
Fax: (708) 325-0450 

Step 11:  Ceiling Kit Assembly.

 



Ceiling can only be installed AFTER the vertical portion of assembly has been completed  

       per previous instructions (See 

Step 1



Prior to installation check Ceiling Assembly Kit for accurate part count. 

Step 11A: Installing Ceiling Angle (C1). 



Installing the ceiling angle (C1) can be accomplished either/or bend in or bend out; refer to Figure (9A-1).  



Attach the Angle (C1) via the provided Carriage Bolt (F2), Washer (F4), Nut (F3) and Mesh Clamp (B10) to  

       the vertical already installed panel (M1).  See Figure (11A-1) for reference. 



Lay in the Mesh Panel (M1) horizontally with legs going up, as it will serve as your Ceiling Panel.  See Figure (11A-1) for reference. 



Attach with provided Carriage Bolt (F2), Mesh Clamp (B10), Washer (F4) and Nut (F3) as shown in Figure (11A-1). 

Fig.

 

11A

1

 

Step 11B:  Ceiling Panel attachment to various verticals. 



When attaching to a ceiling panel to a wall, please see the (

Step 2

)

 

instructions (omit the 2” sweep space note). 



When attaching to a roof support bracket please follow the directions in (

Step 3

)

 

for attaching to a post. 



When attaching to another Ceiling panel please refer to (

Step 5

) for attaching to another panel. 

Summary of Contents for Qwik-Fence


















Reviews: