background image

Horizon Elite 710 Self-Contained

Ambient

Air temperature

100 F/38 C max.

50 F/10 C min.

Water temperature

90 F/32 C max.

45 F/7 C min.

Water pressure – potable

70 psi max. (483 kPa)

10 psi min. (89 kPa)

Heat rejection

710

Air-cooled

8,500 BTU/hr

Ice production

Horizon Elite 710 series, air-cooled 60 Hz

Inlet water  
temperature 
F (C)

Ambient air temperature F (C)

60 (16)

70 (21)

80 (27)

90 (32)

100 (38)

lb (k

g) pr

oduction in 24 hr

50 (10)

787 (357)

759 (345) 705 (320)

639 (290)

603 (274)

60 (16)

750 (341)

702 (319) 666 (302)

624 (283)

570 (259)

70 (21)

707 (321)

681 (309) 636 (289)

586 (266)

542 (246)

80 (27)

677 (307)

629 (286) 611 (277)

559 (254)

518 (235)

90 (32)

642 (291)

600 (272) 580 (263)

539 (245)

497 (226)

Horizon Elite 710 series, air-cooled 50 Hz

Inlet water  
temperature 
F (C)

Ambient air temperature F (C)

60 (16)

70 (21)

80 (27)

90 (32)

100 (38)

lb (k

g) pr

oduction in 24 hr

50 (10)

664 (301) 617 (280)

576 (261)

538 (244)

500 (227)

60 (16)

645 (293) 601 (272)

560 (254)

521 (236)

481 (218)

70 (21)

626 284)

582 (264)

544 (247)

506 (229)

464 (210)

80 (27)

588 (267) 544 (247)

512 (232)

481 (218)

389 (176)

90 (32)

557 (252) 519 (235)

487 (221)

455 (207)

328 (149)

Weight 

Shipping

190 lb (86 kg)

Net

180 lb (82 kg)

Summary of Contents for Horizon Elite HCD710A

















Reviews: