background image

M-6007-Z460FFT(FRT) 

Crate Engine 

GUIDE 

 

 

 

 

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF  

FORD PERFORMANCE PARTS. 

Techline 1-800-367-3788 

Page 3 of 24   

 

 

 

IS-1850-0636

  

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356

 

Please visit www.performanceparts.ford.com for the most current instruction information. 

 

! ! ! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. 

AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD 

PERFORMANCE TECHLINE AT 1-800-367-3788 ! ! ! 

 

 

FORD PERFORMANCE CRATE ENGINE LIMITED WARRANTY 

 

Ford Performance warrants for 24 months or 24,000 miles / 40,000 kilometres, whichever occurs first subsequent 

to the original retail purchase, that it will repair or replace, at its option, any Ford Performance engine part that, 

after inspection, is found to have failed due to a defect in factory supplied material or workmanship. Ford 

Performance may use new or remanufactured parts for replacement. 

 

Covered engine parts include the engine block and cylinder heads, all internally lubricated parts of the engine, including 

pistons, piston rings, piston pins, crankshaft and main bearings, connecting rods and rod bearings, camshaft and 

camshaft bearings, timing chain, timing chain gears, intake and exhaust valves, valve springs, oil pump, push rods, 

rocker arms, valve lash adjusters, hydraulic or mechanical lifters, and valve stem seals, to the extent that the original 

engine contains the referenced warranted part. Parts that require normal manufacturers recommended replacement 

intervals are not covered under this warranty.  

 

In the Province of Quebec, none of the limitations and exclusions below will exclude or restrict the warranty provided for 

in Sections 37 and 38 of the Quebec Consumer Protection Act. This warranty does not preclude the operation of any 

other provincial statute, which in certain circumstances may not allow some of the limitations and exclusions described 

in this warranty. 

 

To the extent allowed by law, loss of time, inconvenience, loss of the use of the vehicle, commercial loss and 

incidental and consequential damages are not covered. There is no other express or implied warranty on these 

Ford Performance engines including, but not limited to, any implied warranty of merchantability or fitness for a 

particular purpose.  

 

This warranty does not cover: 

  Sealed racing engines and other high-performance engines with mechanical lifter camshafts. 

  Parts which are replaced as part of normal maintenance. 

  Engine installation or removal costs. 

  Damage due to improper engine installation, negligence, alteration or accident, including use related to 

competition racing, marine or motorcycle applications or for other non-vehicle usage. 

  Damage due to addition of power adders such as superchargers, turbochargers or nitrous oxide. 

  Engines where the vehicle odometer has been disconnected or the mileage has been altered. 

 

Damage caused by lack of proper maintenance, failure to follow maintenance schedule intervals or failure 

to use or maintain proper type and levels of fluids, fuel, oil and lubricants, including accelerated wear from 

contaminated oil or fuel wash. 

  Damage due to engine overheating or oil starvation. 

  Damage resulting from improper engine tuning including, piston skirt scuffing, damage indicated by head 

gaskets exhibiting burned or crushed fire ring(s), or damage caused by improper combustion, detonation or 

pre-ignition, as indicated by melted, broken or eroded pistons. 
 

Summary of Contents for M-6007-Z460FFT

























Reviews: