7 - 10
ForeRunner
ATM Switch Network Configuration Manual
Signalling
The following two tables summarize the above information. Table 7.1 highlights the actions
taken based on the configurations of the FORE switches on both sides of an interface.
ForeThought versions prior to ForeThought 4.1.x always default to UNI 3.0. Both UNI 3.1 and
UNI 4.0 use SSCOP version 31.
Table 7.1 -
Action Taken Based on Both Switches’ Signalling Channel Configurations
Configured
Version
Peer’s
Configured
Version
Action Taken
UNI 3.0
UNI 3.0
UNI 3.1
UNI 4.0
PNNI 1.0
Auto
SSCOP 30 stack initialized
SSCOP 30 stack initialized; error message displayed on syslog
SSCOP 30 stack initialized; error message displayed on syslog
SSCOP 30 stack initialized; error message displayed on syslog
SSCOP 30 stack initialized; peer changes version to UNI 3.0
UNI 3.1
UNI 3.0
UNI 3.1
UNI4.0
PNNI 1.0
Auto
SSCOP 31 stack initialized; error message displayed on syslog
SSCOP 31 stack initialized
SSCOP 31 stack initialized; error message displayed on syslog
SSCOP 31 stack initialized; misconfiguration
SSCOP 31 stack initialized; peer changes version to UNI 3.1
PNNI 1.0
UNI 3.0
UNI 3.1
UNI4.0
PNNI 1.0
Auto
SSCOP 31 stack initialized; error message displayed on syslog
SSCOP 31 stack initialized; misconfiguration
SSCOP 31 stack initialized; misconfiguration
SSCOP 31 stack initialized
SSCOP 31 stack initialized; peer changes version to PNNI 1.0
if it supports PNNI
UNI 4.0
UNI 3.0
UNI 3.1
UNI4.0
PNNI 1.0
Auto
SSCOP 31 stack initialized; error message displayed on syslog
SSCOP 31 stack initialized; error message displayed on syslog
SSCOP 31 stack initialized
SSCOP 31 stack initialized; misconfiguration
SSCOP 31 stack initialized; peer changes version to UNI 4.0
Auto
UNI 3.0
UNI 3.1
UNI4.0
PNNI 1.0
Auto
SSCOP 30 stack initialized
SSCOP 31 stack initialized
SSCOP 31 stack initialized
SSCOP 31 stack initialized
Both stacks initialized as SSCOP 31 if both sides support UNI
3.1 or UNI 4.0; otherwise, both sides are initialized to SSCOP
30. If both sides support PNNI then, both sides are initialized
to SSCOP 31 and the version is set to PNNI 1.0.
Summary of Contents for forerunner series
