Forest 5201.00.X64X Manual Download | Manualshive

Page: 4 / 13

background image

08/2014 WDOC MULTI REMOTE

www.forestgroup.nl

v1.91

4

FOREST MULTI WALL SWITCH RF - 5201001470

TECHNICAL SPECIFICATION:

● 3V battery CR2032

● transmit range indoor max. 30mtr

● battery life < 3 years

● working temperature -10°C - +50°C

● frequency 433.92MHz

● each channel can control up to 20 receivers

● transmit power max. 10mW

P2 buttons (for programming tubular motor)

OPEN/UP button

STOP button

CLOSE/DOWN button

channel A channel B

battery CR2032

BATTERY EMPTY:

After changing the battery, programmed receivers will stay in memory of remote. Please follow the local
regulations for disposal of the empty battery.

FOREST MULTI WALL SWITCH LED- 5201001480

TECHNICAL SPECIFICATION:

● 12V battery type 27A

● transmit range indoor max. 30mtr

● battery life < 3 years

● working temperature -10°C - +50°C

● frequency 433.92MHz

● each channel can control up to 20 receivers

● transmit power max. 10mW

OPEN/UP button

STOP button

CLOSE/DOWN button

+

channel A channel B

P2 buttons (for programming tubular motor)

BATTERY EMPTY:

After changing the battery, programmed receivers will stay in memory of remote. Please follow the local
regulations for disposal of the empty battery.

«
...
2
3
4
5
6
...
»

Summary of Contents for 5201.00.X64X














Reviews:

No comments

Related manuals for 5201.00.X64X

Brand: Radio Shack Pages: 52

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Uclear Pages: 40

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Parker Pages: 32

Brand: Rayrun Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands