background image

 

07/2016  WDOC Diamond remote

 

                 www.forestgroup.nl 

v1.4

 

 

 

TUBULAR MOTOR 

 

BUILD-IN RECEIVER AND ELECTRONIC LIMIT SETTING

 

 

   

  

 

 
 
 
 

 

 press button on motor, motor will           ①st remote: press P button two times 

             press P button one time 

       turn short to acknowledge 

 
   

 

 

 

 

 

                 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

       

 
 
 
   

 

 

 

 

 

 

 

  2x P 

 

 

 

                 1x P 

 
 

 
 

            within 6 seconds: 
 

        press P button two times 

         ②nd remote: press P button one time 

           press STOP button one time 

 
 

   

 

 

 

 

 

                 

 

 
 
   

 

 

 

 

 

 

 

 

 

 

 

 

  

1x STOP 

   
   

 

            2x P 

 

 

 

 

     

1x P 

 

 

 
 

 
 
 
      

press OPEN button one time 

 

    motor will turn to acknowledge   

            press P button one time 

 

 

 
 

   

 

            1x OPEN 

   

 
   

 

 

 

 

 

 

 

 

 

 

 

 

  

1x P 

 
 

 

 
 

 
    motor will turn to acknowledge   

           to add another channel: 

 

        motor will turn to acknowledge 

          1.press 2xP button of programmed channel, 
          2.select other channel and press P button 

 

 

 

 

 

 

     motor will turn to acknowledge 

 
 

 

 
 CHANGING DIRECTION OF ROTATION: 
   To change the direction of rotation, 

  keep green button on motor pressed 

       for 7 sec, until motor turns to 

acknowledge. 

             

PROGRAMMING REMOTE       

 

    ADD MORE REMOTES OR 

                  TO TUBULAR MOTOR: 

 

              CHANNELS TO TUBULAR MOTOR 

 

        CANCEL ALL REMOTES 

 

Summary of Contents for Diamond









Reviews: