38
Use and maintenance
ATOMIZER ON VISION MULTIFUNCTION MACHINE
those disputes arising from the supply contract or in any other
case where it is required the opinion of a judicial body, the Court
of Vicenza will the only competent.
1.2.1 WARRANTY EXCLUSIONS
The warranty is void (in addition to what is shown in the supply
contract):
- if an error of maneuver and/or collision due to the Operator
occurs;
- if the maximum allowed power limit is exceeded;
- if the damage is attributable to poor maintenance;
- if accessories or applications not supplied or tested by the
Manufacturer were installed on the machine;
- if, following repairs carried out by the User without the consent
of the Manufacturer or due to the assembly of non-original
spare parts, the machine should undergo changes and the
damage could be attributable to such changes;
- if the instructions in this manual have not been observed;
- if exceptional events occur.
Failure to comply with what is described in this manual,
operational negligence, incorrect use of the machine and
the execution of unauthorized changes are the cause of
cancellation, by the Manufacturer, of the warranty granted
to the machine, thus declining every and any liability for
direct and/or indirect damages due to the reasons given
above.
For any repairs or revisions that involve works of a certain
complexity, it is necessary to contact the Authorized Ser-
vice Centers that have specialized personnel or directly
the Manufacturer, which is however at complete disposal
to ensure prompt and accurate technical assistance and
what necessary to restore the full machine efficiency.
Pay attention to the symbols listed below in this manual.
They report a possible danger situation.
DANGER: THIS SIGN WARNS THAT IF THE WOR-
KS DESCRIBED ARE NOT CORRECTLY CARRI-
ED OUT, THEY CAN CAUSE SERIOUS INJURY,
DEATH OR LONG-TERM RISKS FOR HEALTH.
WARNING: THIS SIGN WARNS THAT IF THE WOR-
KS DESCRIBED ARE NOT CORRECTLY CARRIED
OUT, THEY MAY RESULT IN SERIOUS INJURY,
DEATH OR LONG-TERM RISKS FOR HEALTH.
SECTION 1
Description and features of the machine
1.1 INTRODUCTION
This manual contains information, instructions and what is
deemed necessary for the knowledge, proper use and normal
maintenance of the ATOMIZER installed on the VISION model
multifunction machine, manufactured by
«FORT Unipersonale
Srl»
based in Sossano (Vicenza) Italy, hereinafter referred to
as the Manufacturer.
Below are the terms ATOMIZER or even MACHINE, where
machine means the whole atomizer group installed on the
multifunction VISION machine. When using the ATOMIZER,
it is also required to refer to the instructions of the multi-
function VISION machine attached to the machine.
This manual content does not contain a complete description of
the various organs nor a detailed exposition of their operation;
however, the User will find what is normally useful for use in
security and for a good storage of the machine.
From performance and compliance with what is described in
this manual, they depend on the smooth operation, durability
and operating economy of the machine.
1.2 WARRANTY
The Manufacturer warrants its new factory products for a period
of twelve (12) months from the date of purchase.
The engine is warranted according to the terms and conditions
established by the its manufacturer.
Verify, upon receipt, that the machine is intact and complete.
Any complaints must be made in writing within 8 (eight) days
from the date of receipt of the machine.
The warranty includes only the free-of-charge repair or repla
-
cement of those parts that, after careful examination by the
Technical Dept. of the Manufacturer, are found defective (exclu
-
ding the electrical parts, the working tools and consumables).
Any returns must always be agreed with the Manufacturer, and
shipped ex works.
Replacements or repairs of parts under warranty will not extend
in any case the terms thereof.
In any case, the buyer must pay the cost of transport, lubricants,
VAT and any customs duties.
The buyer will be able to assert its rights on the guarantee only
if it has complied with any additional conditions on the provision
of the warranty, also reported in the supply contract.
If it appears that the parties do not intend to submit to arbitration
