Fort WM 600 B, Operating And Maintenance

21

ENGLISH

DESCRIPTION OF FIGURES

Fig. 1 - Overview of the machine.

  1) Nameplate.

  2) Serial number.

  3) Release lever safety brake and insertion cutting ap-

paratus.

  4) Device for locking/unlocking lever (3). Only when 

pressed in the direction indicated by the arrow, al-

lows the actuation of the lever with the consequent 

release of the safety brake and drive of the cutting; 

the release, the lever (3) automatically returns 

in a vertical position by removing traction to the 

transmission belt and activating the braking system 

of the cutting. H) Control cable rotating knives. I) 

Cable insertion brake.

  5) Parking brake lever (only version WM 600 BR).

  6)  System lock brake (only version WM 600 BR).

  7)  Lever insertion forward.

  8)  A device locking/unlocking lever insertion forward. 

Only when pressed in the direction indicated by the 

arrow, allows the operation of the lever, and acti-

vate the forward run of the machine; the lever is 

released, the machine stops and the lever remains 

in a vertical position.

  9)  Lever inserting reverse; (only on version WM 600 

BR). The levers 8 and 9, can't be operated simulta-

neously.

10) Throttle Lever: E = stop position of the engine. F = 

position of maximum engine rpm.

11) Hand lever handlebar height adjustment (n. 2).

12) Hand lever manual motor controllers.

13) Plug with engine oil dipstick.

14) Fuel tank cap.

15) Hand lever mounting bracket towel rake.

16) Engine air filter.

17) Shelter in canvas with metal frame.

18) Cylinder scatter grass and support cutting knives.

19) No 4 floating knives for cutting grass. 

G = direction 

of rotation cutting apparatus.

20) Screw fixing the knife float.

21)  Towel rake adjustable width.

Fig. 2 - Overall dimensions of the machine.

Fig. 3 - Rod marches.

 Push forward all fits 1st gear, 

halfway back you insert the second, the whole back 

third.

Fig. 4 - Anchor points for lifting the machine.

Fig. 5 - 1) Fixing screws shelter in canvas.

Fig. 6 - Slide cutting height adjustment. 1) Screw 

fixing slides. - A) Height of the slide.

Fig. 7 - Safety signs and their location on the machine 

(for their description see section 2.2 Safety signs).

TABLE OF CONTENTS

Declaration of conformity ............................................ 2

SECTION 1. Description and specifications of the 

machine

1.1  

Foreword. ...................................................... 22

1.2  

Warranty ....................................................... 22

1.2.1  Warranty exclusions ..................................... 22

1.3  

Identification of the machine

 ......................... 23

1.4 

Description of the machine and authorized ... 23

1.4.1  Use of the machine ....................................... 23

1.4.2  Unauthorized use of the machine .................. 22

1.4.3  Equipment interchangeable on demend ........ 24

1.4.4  Control and driving position .......................... 24

1.5 

Protections and safety devices ...................... 24

1.5.1  Noise level ..................................................... 24

1.5.2   Vibrations level ............................................. 24

1.6 

Technical specifications

 ................................ 24

SECTION 2. Safety and prevention

2.1 Safety ............................................................ 25

2.1.1  Words used ................................................... 25

2.1.2  General safety regulation .............................. 25

2.2 

Safety signals ................................................ 26

2.3 

Safety while operating and maintenaing ........ 26

SECTION 3: Transport

3.1 Transport ...................................................... 27

SECTION 4: Use

4.1 

Before using the machine ............................. 28

4.1.1  Unpacking the machine ................................. 28

4.1.2  Installing the whells ...................................... 28

4.1.3  Adjustment of the handlebars ....................... 29

4.1.4.  Installing the skids for the adjustment of 

tthe cutting height ......................................... 29

4.1.5  Installing a canvas shelter ............................. 29

4.2 Start-up ......................................................... 29

4.3 

Progress - engagement of the gear ............... 30

4.4 

Innesto fresa e innesto ruota motrice ........... 28

4.4 

During operation ........................................... 30

4.4.1  Use of the machinee on slopes ..................... 30

4.4.2 Parking .......................................................... 31

4.5 

Stopping of the engine .................................. 31

4.6 

After use ....................................................... 31

SECTION 5: Routine maintenance

5.1 

General information ...................................... 31

5.2 

Engine maintenance ...................................... 31

5.3 

Machine maintenance ................................... 31

5.3.1  Maintenance of the chain and the drive belt .. 31

5.3.2  Belt of the cutting device ............................... 32

5.3.3  Safety brake .................................................. 32

5.3.4  Checking the cables ...................................... 32

5.3.5  Replacing the canvas shelter ......................... 32

5.3.6  Replacing the knives ..................................... 32

5.4 

Extraordinary maintenance ........................... 33

5.5 

Setting at rest ................................................ 33

5.6 

Machine dismantling ..................................... 33

5.7 

Spare parts ................................................... 33

5.8 Troubleshooting ............................................ 33