Fortin E400 RF641W Quick Installation Manual Download

Page: 4 / 8

TO DISABLE READY MODE

COLD START MODE

REMOTE START / ALARM DIAGNOSTICS

STANDARD

• Open any door(s)

• Open the hood

• Disengage the

parking brake

WITH NEUTRAL

SAFETY SWITCH

• Transmission not in

neutral position

• Open the hood

• Disengage the

parking brake

Note : If the parking

lights flash 3 times

when Remote-

Starting, Ready Mode

is not enabled.

READY MODE

REMOTE STARTER

Parking Light flashes (before starting) :

Ready Mode disabled

Valet Mode activated (The LED

is on)

Hood open

Parking Light flashes (after starting) :

Normal stop (Brake, Park Brake)

Runtime expired or shut down by

Transmitter

No tachometer signal

Hood open

Over crank threshold (8 sec-

onds)

ALARM DIAGNOSTICS

Parking Light flashes (after disarm) :

Door open – zone 3

Shock sensor – zone 4

Hood open – zone 5

Trunk open – zone 6

Auxiliary IN– zone 7

X INDICATES THE NUMBER OF TIMES

THE PARKING LIGHTS WILL FLASH

AVERTISSEMENT

The engine’s tachometer

signal must be detected by

the remote starter to operate

in a manual transmission.

Tachometer is connected

directly to the vehicle:

Option 20: Mode 1 or 3

- or -

Tachometer is obtained

Through the interface

module EVO-ALL or EVO-

CHR:Option 20: Mode 1 or 6

Make sure that

all doors are

closed and the

transmission is

in the NEUTRAL

position.

While the

engine is

running.

Engage the

parking

brake.

Release the

brake pedal.

NOTE

If the

parking

lights flash

3 timed:

Verify the

Tachometer

signal.

Remove the

key from the

ignition barrel.

The vehicle

will remain

running with the

Remote-Starter.

Exit the vehicle

and close all of

the doors.The

Remote-Starter will

stop running once

all the doors are

closed.

ANALOG TACH LEARNING (PURPLE WIRE)

READY MODE FOR NEUTRAL SAFETY SWITCH

WARNING

Press and release 20 times the

valet-switch. The park-lights will

flash and the horn/siren will chirp

once to confirm.

X20

A long chirp indicates

tach learning failed. If

the procedure fails or

to re-learn the tach

setting, re-start the

procedure.

MULTI-

LINK

PROGRAM REMOTE-STARTER

OPTIONS WITH ONE CLICK

The MULTI-LINK displays diagnostic

information and changes the remote-

starters programming options.

IGN

START

OFF

Press and release

the brake-pedal

once.

READY MODE FOR NEUTRAL SAFETY SWITCH

START

Start the engine

with the key.

TACH LEARNING

Make sure that the

transmission is in the

NEUTRAL position.

Press and hold

the valet-switch until the

LED flashes, then release.

Engage the parking

brake.

MULTI-LINK

Remove the key from the

ignition barrel.The vehicle is

ready to start. (and not running)

NOTE: This feature will be functional only if the Tach is detected by a bypass module or

connected directly to the vehicle.

Press and release 20 times the

valet-switch. The park-lights will

flash and the horn/siren will chirp

once to confirm.

X20

A long chirp indicates

tach learning failed. If

the procedure fails or

to re-learn the tach

setting, re-start the

procedure.

MULTI-

LINK

PROGRAM REMOTE-STARTER

OPTIONS WITH ONE CLICK

The MULTI-LINK displays diagnostic

information and changes the remote-

starters programming options.

IGN

START

OFF

Press and release

the brake-pedal

once.

READY MODE FOR NEUTRAL SAFETY SWITCH

START

Start the engine

with the key.

TACH LEARNING

Make sure that the

transmission is in the

NEUTRAL position.

Press and hold

the valet-switch until the

LED flashes, then release.

Engage the parking

brake.

MULTI-LINK

Remove the key from the

ignition barrel.The vehicle is

ready to start. (and not running)

NOTE: This feature will be functional only if the Tach is detected by a bypass module or

connected directly to the vehicle.

Press and hold the valet

switch until the Parking

lights turn ON, the

horn/siren will chirp.

DISARM / ENTER / EXIT VALET MODE

STEP 1

STEP 2

to disarm

the system

FMH

2-W

System armed :

DEL flash

Insert the

key and

turn it to

the ignition

(ON/RUN)

position.

Within 10

seconds

press and

release

the Valet

switch

or the

antenna

button 3

times.

FMH

2-W

System disarmed

LED is OFF

FMH

2-W

to enter and

exit valet

mode

FMH

2-W

System disarmed :

LED is OFF

FMH

2-W

System disarmed

and in valet

mode :

LED is ON.

Press and release the FUNCTION button, within 12

seconds simultaneously press and and hold the LOCK and START buttons for 1

second. The remote’s Green LED will flash and beep once to confirm. The park

ing lights will flash once.

TO DISABLE

•

Press and release the FUNCTION button, within 12 seconds simultaneously

press and and hold the LOCK and START buttons for 1 second. The remote’s

Green LED will flash and beep once to confirm. The parking lights will flash

twice

• Put the Remote-Starter/alarm into Valet

• Remote-Start the vehicle

• Open the hood

• Press the brake pedal

• Turn the key to the ignition position.

• Disable Ready Mode (manual transmission).

Push the

START button

(3sec.). The

parking lights

will flash once

and then

remain on.

Press the START

button (3sec.) the

horn/siren will chirp 3

times to confirm tach

learning.

ONE

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle itself or to
the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide has been written for
trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.

By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must be cut.
Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an automatic
transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the system is considered
an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual
transmission vehicle.Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects.

This module must be install by qualified technician. This instruction guide may change without notice. To

download the installation guide, user guide, or the latest quick installation guide, visit:

www.fortin.ca

Technical support:

TEL: 514-255-4357

1-877-336-7797