White
#14
Brown
#18
Red
#14
Red
#14
Red
#22
Power
Power
(utility)
Power
Parklights
Ign/Acc/Start
Tachometer
Foot-Brake
Door Pin Pos
Trunk/Hatch (open)
Lock
Starter
Parklight
After Shutdown
(-) while running
Purple
White
Orange
White/Black
Dk. Blue
White/Red
Yellow/Red
Yellow/Black
Brown/White
Lt. Green
Lt. Green/Black
Lt.Blue
24
8
Ignition
Starter
Black
Black
Black
Red White
Ignition Switch
Programming LED
(4pin)
Antenna
(4pin)
RS-232 Data-Link
(2pin)
Valet/Programming Button
Shock Sensor
(3 pin)
Extra LED
(2 pin)
Aux.1
Aux.2
~
PROGRAMMING REMOTE TRANSMITTER(S)
INPUT
OUTPUT
WIRING / CONNECTION GUIDE
The system can learn up to a maximum of 4 transmitters.
Any
can be stored in more than 1 memory slot.
When a 5th
is learned the 1st remote is errased (FIFO).
transmitters
transmitter
STEP
1
IGN
Turn the
Ignition on.
STEP
2
Press and
hold
the valet-
switch until
the LED
flashes, then
release.
STEP
3
Press and
release the
valet-switch
once. The
park-lights
will flash to
confirm.
STEP
5
On each Transmitter
press the LOCK
button once
(maximum 4
transmitters), the
park-lights will flash
to confirm.
STEP
4
Press and
release the
brake-pedal
once.
2
Copyright © 2008, FORTIN AUTO RADIO INC
ALL RIGHTS RESERVED
X1
FSA-206
Automatic and Manual Remote Starter / Alarm
QUICK INSTALLATION GUIDE
Made in Canada - Rev. R - 11 / 11 / 2008
W e b
s i t e :
h t t p : / / i f a r . c a / f i l e s / F S A 2 0 6 /
1
4
3
24 12
1
13
8
1
5
4
Cut loop for automatic
transmission mode.
Cut loop for automatic
transmission mode.
S
P
EC
IAL U
N
IT
WEB
UPDATE
COMPATIBLE
Arm
IGN
START
OFF
Release the brake
pedal.
4
Push the START button. The
parking lights will flash once
and then remain on.
Remove the key from the
ignition barrel.The vehicle will
remain running with the
Remote-Starter.
5
6
Exit the vehicle and close all of the
doors.The Remote-Starter will
stop running once all the doors
are closed.
Press and release 20 times the
valet-switch. The park-lights will
flash and the horn/siren will chirp
once to confirm.
X20
Press TRUNK button, the
horn/siren will chirp 3 times
to confirm tach learning.
A long chirp indicates
tach learning failed. If
the procedure fails or
to re-learn the tach
setting, re-start the
procedure.
3x
4x
5x
6x
7x
8x
9x
Parking Light Flashes (after disarm)
Door open
Shock sensor
Hood open
Trunk open
Auxilliary IN
Tilt Sensor
Ignition
1x
3x
4x
5x
6x
7x
Parking Light Flashes (after starting)
Normal stop Park Brake, Brake
Runtime expired or shut down by
No tachometer signal
Hood open
Over crank threshold
seconds
(
)
remote
(8
)
RPM over-rev (high tach)
Press simultaneously
UNLOCK and START
buttons for 1 second
until the parking lights
flash once.
REMOTE STARTER DIAGNOSTICS
3x
4x
5x
Parking Light Flashes (before starting)
Ready mode disabled
Valet mode activated The LED is on
Hood open
(
)
ALARM DIAGNOSTICS
TO DISABLE
TO ENABLE
Put the Remote-Starter/alarm into Valet
Remote-Start the vehicle
Open the hood
Press the brake pedal
Turn the key to the ignition position.
Disable Ready Mode (manual
transmission).
Automatic and Manual Remote Starter / Alarm
QUICK INSTALLATION GUIDE
Made in Canada - Rev. R - 11 / 11 / 2008
W e b
s i t e :
h t t p : / / i f a r . c a / f i l e s / F S A 2 0 6 /
MULTI-
LINK
PROGRAM REMOTE-STARTER
OPTIONS WITH ONE CLICK
The MULTI-LINK displays diagnostic
information and changes the remote-
starters programming options.
IGN
START
OFF
Remove the key from the
ignition barrel.The vehicle is
ready to start. (and not
running)
STANDARD
WITH NEUTRAL SAFETY SWITCH
•
Open any door(s)
Open the hood
Disengage the parking brake
•
•
•
Transmission not in neutral position
•
Open the hood
•
Disengage the parking brake
Note :
If the parking
lights flash 3 times when
Remote-Starting, Ready
Mode is not enabled.
4
Press and release
the brake-pedal
once.
5
3
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle
itself or to the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide
has been written for trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully
before beginning any work.
By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must be
cut. Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an
automatic transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the
system is considered an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is
install on a manual transmission vehicle.
COLD START MODE
COLD START MODE
REMOTE START / ALARM DIAGNOSTICS
TO DISABLE READY MODE
READY MODE FOR NEUTRAL SAFETY SWITCH
To download the installation guide, user guide, or the latest quick installation guide, visit:
http://ifar.ca/files/FSA206/
STEP
6
OFF
Turn the
Ignition off.
STEP
7
Press and
release the
brake-pedal
once.
Yellow
#14
Orange
#14
Pink
#14
Black
#18
Starter
Accessory
Ignition
Ground
Hood Pin
E-Brake
Door Pin Neg.
Trunk/Hatch Pin
Starter Kill
Unlock
Disarm
Ignition
Accessory
Horn
Siren
Aux.IN
Grey
Brown
Dk. Green
Pink
Yellow
White/Green
Yellow/Green
Pink/Black
Orange/Black
Red/Black
Red
Purple/White
1
1
To Vehicle
To Vehicle
Starter-Kill / Anti-Grind Relay
Starter-Kill / Anti-Grind Relay
See programming guide, Function #10
See programming guide, Function #10
1
&
Make sure that all doors are
closed and the transmission
is in the NEUTRAL position.
While the engine is
running. Engage the
parking brake.
2
3
START
Start the engine
with the key.
1
2
3
IGN
X3
Insert the key and turn it to the
ignition RUN/ON position.
(
)
Within 10 seconds press and
release the Valet switch 3
times.
FSA-206
TACH LEARNING
(4pin)
RS-232 Data-Link
READY MODE
WARNING
1
Make sure that the
transmission is in the
NEUTRAL position.
3
Press and hold
the valet-switch until the
LED flashes, then release.
Black
Black
Black
Red White
The LED will turn ON solid
and remain ON.
Engage the parking
brake.
2
MULTI-LINK
S
P
EC
IAL U
N
IT
ENTER/EXIT VALET MODE
Neutral Safety Switch for manual transmission vehicle
7
7
7 0 3 5 0 0 0 1 1 1
Optional Relay
